MCP1701AT-3302I/MB Microchip Technology, MCP1701AT-3302I/MB Datasheet - Page 9

• Manufacturer Part Number: MCP1701AT-3302I/MB
• Description: IC LDO REG 150MA 3.3V SOT-89-3
• Manufacturer: Microchip Technology

Specifications of MCP1701AT-3302I/MB

• Package / Case: SC-62, SOT-89, TO-243 (3 Leads + Tab)
• Regulator Topology: Positive Fixed
• Voltage - Output: 3.3V
• Voltage - Input: Up to 10V
• Voltage - Dropout (typical): 0.4V @ 150mA
• Number Of Regulators: 1
• Current - Output: 150mA (Min)
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Number Of Outputs: 1
• Polarity: Positive
• Input Voltage Max: 10 V
• Output Voltage: 3.3 V
• Output Type: Fixed
• Dropout Voltage (max): 0.7 V @ 150 mA
• Output Current: 0.15 A (Min)
• Line Regulation: 0.3 %/V
• Load Regulation: 2.72 %
• Voltage Regulation Accuracy: 2 %
• Maximum Power Dissipation: 500 mW
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• Primary Input Voltage: 4.3V
• Output Voltage Fixed: 3.3V
• Dropout Voltage Vdo: 380mV
• No. Of Pins: 3
• Voltage Regulator Case Style: SOT-89
• Operating Temperature Range: -40°C To +85°C
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Current - Limit (min): -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

3.0
The descriptions of the pins are listed in
TABLE 3-1:
3.1
Regulator ground. Tie GND to the negative side of the
output and the negative side of the input capacitor.
Only the LDO bias current (2 µA, typ.) flows out of this
pin, there is no high current. The LDO output regulation
is referenced to this pin. Minimize voltage drops
between this pin and the negative side of the load.
3.2
Connect V
positive terminal of the output capacitor. The positive
side of the output capacitor should be physically
located as close as possible to the LDO V
current flowing out of this pin is equal to the DC load
current.
© 2007 Microchip Technology Inc.
SOT-23A
Pin No.
1
2
3
PIN DESCRIPTIONS
Ground Terminal (GND)
Regulated Voltage Output (V
OUT
to the positive side of the load and the
Pin No.
SOT-89
PIN FUNCTION TABLE
1
3
2
Pin No.
TO-92
1
3
2
Table
OUT
pin. The
OUT
3-1.
Name
V
GND
V
OUT
IN
)
Ground Terminal
Regulated Voltage Output
Unregulated Supply Input
3.3
Connect the input supply voltage and the positive side
of the input capacitor to V
regulators, low source impedance is necessary for the
stable operation of the LDO. The amount of
capacitance required to ensure low source impedance
will depend on the proximity of the input source
capacitors or battery type. The input capacitor should
be physically located as close as possible to the V
pin. For most applications, 1 µF of capacitance will
ensure stable operation of the LDO circuit. For
applications that have load currents below 100 mA, the
input capacitance requirement can be lowered. The
type of capacitor used can be ceramic, tantalum or
aluminum electrolytic. The low equivalent series
resistance characteristics of the ceramic will yield
better noise and PSRR performance at high frequency.
The current flow into this pin is equal to the DC load
current, plus the LDO bias current (2 µA, typical).
Unregulated Supply Input (V
Function
IN
MCP1701A
. Like all low-dropout linear
DS21991C-page 9
IN
)
IN