CS8361YDPSR7G ON Semiconductor, CS8361YDPSR7G Datasheet - Page 4

• Manufacturer Part Number: CS8361YDPSR7G
• Description: IC REG LDO DUAL 5V MCRPWR D2PAK
• Manufacturer: ON Semiconductor

Specifications of CS8361YDPSR7G

• Regulator Topology: Positive Fixed
• Voltage - Output: 5V
• Voltage - Input: 6 ~ 26 V
• Voltage - Dropout (typical): 0.4V @ 250mA, 0.4 @ 100mA
• Number Of Regulators: 2
• Current - Output: 250mA, 100mA
• Current - Limit (min): 275mA, 125mA
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Surface Mount
• Package / Case: TO-263-7, D²Pak (7 leads + Tab), TO-263CA
• Number Of Outputs: 2
• Polarity: Positive
• Input Voltage Max: 60 V
• Output Voltage: 5 V
• Output Type: Fixed
• Dropout Voltage (max): 0.15 V at 100 uA
• Output Current: 100 mA, 250 mA
• Line Regulation: 50 mV
• Load Regulation: 50 mV
• Voltage Regulation Accuracy: 2 %
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• Voltage Regulator Type: Linear
• Topology: LDO
• Regulator Output Type: Fixed
• Polarity Type: Positive
• Input Voltage (max): 60V
• Package Type: D2PAK
• Output Voltage Accuracy: ±2%
• Operating Temp Range: -40C to 125C
• Operating Temperature Classification: Automotive
• Dropout Voltage@current (max): 0.15@100uA/0.7@250mA
• Dropout Voltage@current (typ): 0.1@100uA/0.4@250mA
• Pin Count: 7 +Tab
• Mounting: Surface Mount
• Quiescent Current (max): 50mA
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: CS8361YDPSR7G; CS8361YDPSR7GOSTR

ENABLE Function
V
1.4 V (Typ), V
millivolts of hysteresis to prevent spurious output activity
during power−up or power−down.
RESET Function
controlled by a low voltage detection circuit sensing the
V
RESET output stays below 1.0 V (0.1 V Typ) when V
is as low as 1.0 V to ensure reliable operation of
microprocessor− based systems.
PACKAGE PIN DESCRIPTION
TRK
STBY
The ENABLE function switches the output transistor for
The RESET is an open collector NPN transistor,
D
2
PAK, 7 Pin
on and off. When the ENABLE lead voltage exceeds
(5.0 V) output voltage. This circuit guarantees the
1
2
3
4
5
6
7
PACKAGE PIN #
B+
TRK
turns off. This input has several hundred
2, 7, 10, 11,
4, 5, 12, 13
SO−16L
14, 15
V
For V
*C1 is required if regulator is located far from power supply filter.
**C2 and C3 are required for stability.
C1*
0.1 mF
16
1
3
6
8
9
TRK
Figure 2. Test and Application Circuit, 5.0 V, 8.0 V Regulator
TRK
∼ V
STBY
∼ 8.0 V, R1/R2 ∼ 0.6
V
GND
IN
(1 + R1/R2)
CS8361
PIN SYMBOL
ENABLE
RESET
V
V
GND
ENABLE
CIRCUIT DESCRIPTION
STBY
V
Adj
NC
TRK
RESET
IN
V
V
STBY
http://onsemi.com
TRK
Adj
STBY
4
R3
R1
Standby output voltage delivering 100 mA.
Input voltage.
Tracking output voltage controlled by ENABLE delivering 250 mA.
Reference ground connection.
Resistor divider from V
V
Provides on/off control of the tracking output, active LOW.
CMOS compatible output lead that goes low whenever V
out of regulation.
No connection.
V
but is rated for 250 mA. The output is configured as a
tracking regulator of the standby output. By using the
standby output as a voltage reference, giving the user an
external programming lead (Adj lead), output voltages from
5.0 V to 20 V are easily realized. The programming is done
with a simple resistor divider (Figure 2), and following the
formula:
lead to the V
TRK
TRK
This output uses the same type of output device as V
If another 5.0 V output is needed, simply connect the Adj
C3**
10 mF
ESR < 8.0 W
. If tied to V
5.0 V, 100 mA
Output Voltage
V TRK + V STBY
R2
C2**
10 mF
ESR < 8.0 W
TRK
SW 8.0 V,
250 mA
TRK
, V
output lead.
TRK
TRK
FUNCTION
to Adj. Sets the output voltage on
will track V
(1 ) R1 R2) ) I Adj
V
RESET
I/O
GND
DD
STBY
MCU
.
STBY
R1
STBY
falls
,