HM2J08PE5110N9LF FCI, HM2J08PE5110N9LF Datasheet
HM2J08PE5110N9LF
Specifications of HM2J08PE5110N9LF
Related parts for HM2J08PE5110N9LF
HM2J08PE5110N9LF Summary of contents
Page 1
... Millipacs HM Right Angle Headers ® Millipacs HM 5 & 8 Row Receptacle & Right Angle Header MPACS 5R RA RCP MPACS 8R RA RCP MPACS 5R RA HDR Copyright 2001 FCI USA, INC. Form E-3334 02/12/01 APPLICATION SPECIFICATION Application Specification PDM: Rev:B NUMBER GS-20-022 PAGE REVISION ...
Page 2
... Removal tooling for the clip on cover shield ....................................................................................20 11.2. Removal tooling for one piece cover shield.....................................................................................20 11.3. Removal tooling for the 5+8 row connector.....................................................................................21 12. REVISION RECORD ...............................................................................................................................22 Copyright 2001 FCI USA, INC. Form E-3334 02/12/01 APPLICATION SPECIFICATION PDM: Rev:B NUMBER GS-20-022 PAGE ...
Page 3
... Millipacs HM right angle press-fit receptacles and right angle headers intended to provide general guidance for process development and the use of FCI application tooling. It should be recognized that no single process will work under all customer applications and that customers should develop processes to meet individual needs. However, if the processes vary greatly from the recommended one, FCI cannot guarantee acceptable results ...
Page 4
... FCI product drawings and specifications are available by accessing the FCI website or contacting the FCI Technical Service. In the event of a conflict between this specification and the product drawing, the drawing takes precedence. Customers should refer to the latest revision level of FCI product drawings for appropriate product details. ...
Page 5
... To enable proper application and repair/removal of the receptacles, there are recommended keep-out zones (see Figure 8). 5.1. Shielded right angle receptacle connectors 5.1.1. 5 Row connector with one piece cover shield Copyright 2001 FCI USA, INC. Form E-3334 02/12/01 APPLICATION SPECIFICATION Figure 5 -- Keep-out Zones PDM: Rev:B ...
Page 6
... Application Guide ® Millipacs HM 5 and 8 Row Right Angle Signal Receptacles ® Millipacs HM Right Angle Headers 5.1.2. 8 Row connector with one piece cover shield Copyright 2001 FCI USA, INC. Form E-3334 02/12/01 APPLICATION SPECIFICATION Figure 6 -- Keep-out Zones PDM: Rev:B NUMBER GS-20-022 PAGE ...
Page 7
... Application Guide ® Millipacs HM 5 and 8 Row Right Angle Signal Receptacles ® Millipacs HM Right Angle Headers 5.1.3. 8 Row connector with clip on shield Copyright 2001 FCI USA, INC. Form E-3334 02/12/01 APPLICATION SPECIFICATION Figure 7 -- Keep-out Zones PDM: Rev:B NUMBER GS-20-022 PAGE REVISION ...
Page 8
... Connectors with a Service Center can be set up with Coding Keys which create defined intermatable pairs preventing all electrical contact to any connector outside of the coded configuration. Coding Keys are inserted into the connector Service Center using FCI tool HM2Y197E. Figure 8 -- Coding Keys Copyright 2001 FCI USA, INC. ...
Page 9
... B (22pos.) PAY307A45 (***) : PAY308A2 is 50mm long. In case of 19 and 22 pos. on request. (**) : not available on IMPRESS 500M+ and Baby IMPRESS (*) : adapter is only needed in case of shielded connectors Remark : Copyright 2001 FCI USA, INC. Form E-3334 02/12/01 APPLICATION SPECIFICATION ® & 8 row receptacle is defined in Table 1: Table 1 ...
Page 10
... The part numbers for the headers adapters are on request. Tools for the IMPRESS 1000 are the same as for the IMPRESS 500 with LMT. Tools for the IMPRESS 2000 are on request. Copyright 2001 FCI USA, INC. Form E-3334 02/12/01 APPLICATION SPECIFICATION ® ...
Page 11
... Anvil (BOTTOM TOOL) The PCB Support provides a support surface during insertion and includes clearance areas for the press-tails as protrude through the board. FCI offers various PCB Support sizes as listed Table 1. When applying receptacles (headers) that are stacked end-to-end, a longer Anvil can be used. ...
Page 12
... For more information, contact your local Customer Service Representative. FCI provides a range of state-of-the-art press-fit insertion machines. The IMPRESS family has the following offerings: IMPRESS 2000: a modular based fully automated pick-and-place insertion machine. ...
Page 13
... Note : The tools between the IMPRESS machines (except the IMPRESS 2000) are interchangeable. Copyright 2001 FCI USA, INC. Form E-3334 02/12/01 APPLICATION SPECIFICATION Table 2 1000 XXL ...
Page 14
... To ensure proper insertion, RECEPTACLES (HEADERS) MUST BE CENTERED BENEATH THE PRESS RAM. Offset loading may result in improper seating of the receptacle (header) and mating problems. Copyright 2001 FCI USA, INC. Form E-3334 02/12/01 APPLICATION SPECIFICATION Figure 11 – Insertion Procedure PDM: Rev:B ...
Page 15
... Inserting to a certain pressure will yield more consistent results than inserting to a set distance. Be sure to follow any safety requirements associated with the application equipment. Remove assembly from insertion press. Inspect product for proper application. Copyright 2001 FCI USA, INC. Form E-3334 02/12/01 APPLICATION SPECIFICATION Recommended Max Force Setting For Application Press 45 N (10 ...
Page 16
... The Cover Shield is an optional component and is applied to the bottom side of the PCB opposite the side the connector is mounted on for the purpose of bottom side electrical shielding. There are two Cover Shield designs that are available (Shown in Figures 13 and 14). Copyright 2001 FCI USA, INC. Form E-3334 02/12/01 APPLICATION SPECIFICATION Figure 13 – ...
Page 17
... Millipacs HM Right Angle Headers 9.1. One piece cover shield with row receptacle connectors To Install the Clip on Cover Shield Identify the FCI Application tool from the information below. Description Press Toolkit for 8 row connectors Toolkit for 5 row connectors Insert the Cover Shield into the Application tool as defined by the application tool instructions. ...
Page 18
... Place the tool with the shield over the connector pins and by squeezing the tool manually the shield is pressed over the press fit pins. For more detail information, check the instruction manual of the tool. Copyright 2001 FCI USA, INC. Form E-3334 02/12/01 APPLICATION SPECIFICATION ...
Page 19
... PCB but not crushed (see Figure 16). A larger gap beneath the standoffs may indicate that the receptacle (header) is not seated parallel to the board. This can cause receptacle (header) misalignment with adjacent Millipacs Figure 16 -- Proper Receptacle (header) assembly Copyright 2001 FCI USA, INC. Form E-3334 02/12/01 APPLICATION SPECIFICATION ® ...
Page 20
... Figure 17 -- Shielding Removal tooling HM2Y463 Place the tool over the shielding and by turning the handle the shield will be extracted from the PCB. For more detail information, check the instruction manual of the tool. Copyright 2001 FCI USA, INC. Form E-3334 02/12/01 APPLICATION SPECIFICATION ...
Page 21
... The Xcelite Pliers are for removal of the top shield. • The hand tool can be adjusted to remove a connector in the middle of the row. • A manual force of 20 – 30 lbs is required to properly operate the Removal Tool. Copyright 2001 FCI USA, INC. Form E-3334 02/12/01 APPLICATION SPECIFICATION PDM: Rev:B NUMBER ...
Page 22
... HM 5 and 8 Row Right Angle Signal Receptacles ® Millipacs HM Right Angle Headers 12. REVISION RECORD REV PAGE A ALL INITIAL RELEASE B 4/22 Plating Performance Level Added Copyright 2001 FCI USA, INC. Form E-3334 02/12/01 APPLICATION SPECIFICATION DESCRIPTION PDM: Rev:B NUMBER GS-20-022 PAGE REVISION AUTHORIZED BY DATE T. De Rooster ...