NFR0300001008JAC00 Vishay, NFR0300001008JAC00 Datasheet - Page 6

• Manufacturer Part Number: NFR0300001008JAC00
• Description: RES 1.0 OHM 3W 5% MF FUSIBLE
• Manufacturer: Vishay
• Series: NFR03r

Specifications of NFR0300001008JAC00

• Temperature Coefficient: ±200ppm/°C
• Resistance (ohms): 1
• Power (watts): 3W
• Composition: Metal Film
• Features: Flame Proof, Fusible
• Tolerance: ±5%
• Size / Dimension: 0.209" Dia x 0.768" L (5.30mm x 19.50mm)
• Lead Style: Through Hole
• Package / Case: Axial
• Resistance In Ohms: 1.00
• Case: Axial
• Resistance: 1ohm
• Resistance Tolerance: ± 5%
• Power Rating: 3W
• Resistor Element Material: Metal Film
• Resistor Case Style: Axial Leaded
• No. Of Pins: 2
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Height: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: 2306 210 13108; 230621013108; 5093FM1R000J08AFX; PPC1.0ETB

www.vishay.com
6
NFR01, NFR02, NFR03
Vishay BCcomponents
PERFORMANCE
IEC
60115-1
CLAUSE
4.24
4.16
4.16.2
4.16.3
4.16.4
4.19
4.23
4.23.2
4.23.3
4.23.4
4.23.6
4.22
4.17
4.18
4.29
4.7
4.6.1.1
METHOD
21 (Ua1)
60068-2
45 (XA)
21 (Ub)
21 (Uc)
14 (Na)
30 (Db)
30 (Db)
20 (Tb)
20 (Ta)
3 (Ca)
21 (U)
2 (Ba)
1 (Aa)
6 (Fc)
TEST
IEC
-
-
Bending half number
Insulation resistance
Torsion other half of
Component solvent
Tensile all samples
Climatic sequence
remaining cycles
Rapid change of
Voltage proof on
Robustness of
soldering heat
Resistance to
(accelerated)
(accelerated)
(after ageing)
terminations:
steady state
temperature
Solderability
Damp heat,
Damp heat,
of samples
Damp heat
resistance
insulation
Vibration
Dry heat
samples
TEST
Cold
For technical questions, contact: [e-mail]
Fusible Power Metal Film Leaded
3 x 360° in opposite direction
90 % to 100 % RH; 1 cycle
Endurance by sweeping;
leads immersed 2 mm in
displacement 1.5 mm or
5 days; 25 °C to 55 °C
immersed in flux 600,
Solder bath method;
loaded with 0.01 Pn
24 h; 25 °C to 55 °C
Load 5 N; 4 x 90°
acceleration 10 g;
Isopropyl alcohol;
6 mm from body;
10 Hz to 500 Hz;
Load 10 N; 10 s
90 to 100 % RH
56 days; 40 °C;
30 min at UCT;
(235 ± 5) °C for
V-block method
V-block method
16 h at 155 °C;
MIL STD 202E
90 to 95 % RH
30 min at LCT;
LCT = - 55 °C;
UCT = 155 °C;
PROCEDURE
(350 ± 10) °C;
solder bath at
during 1 min,
during 1 min,
16 h, 155 °C
6 h (3 x 2 h)
2 h, - 55 °C
(2 ± 0.5) s
500 V
5 cycles
500 V
for 3 s
Resistors
RMS
DC
± (1 % R + 0.05 Ω) ± (1 % R + 0.05 Ω) ± (2 % R + 0.05 Ω)
NFR01
PERMISSIBLE CHANGE (ΔR)
No flashover or breakdown
± (0.5 % R + 0.05 Ω)
± (0.5 % R + 0.05 Ω)
± (1 % R + 0.05 Ω)
No visible damage
REQUIREMENTS
No visual damage
no visible damage
± (3 % R + 0.1 Ω)
± (3 % R + 0.1 Ω)
R
R
(≥ 95% covered);
R
ins
ins
ins
Good tinning
No damage
min. 10
min. 10
min. 10
NFR02
3
3
4
Document Number: 30256
MΩ
MΩ
MΩ
Revision: 06-Dec-07
NFR03