71M6511-IGTR/F Maxim Integrated Products, 71M6511-IGTR/F Datasheet - Page 41

• Manufacturer Part Number: 71M6511-IGTR/F
• Description: IC ENERGY METER RESIDENT 64-LQFP
• Manufacturer: Maxim Integrated Products
• Type: Metering SoCr

Specifications of 71M6511-IGTR/F

• Mounting Style: SMD/SMT
• Package / Case: LQFP-64
• Core: 80515 MPU
• Data Bus Width: 32 bit
• Data Ram Size: 7 KB
• Device Million Instructions Per Second: 5 MIPS
• Interface Type: UART
• Maximum Clock Frequency: 70 Hz
• Maximum Operating Temperature: + 85 C
• Number Of Programmable I/os: 12
• Operating Supply Voltage: 3.3 V
• Processor Series: 71M6511
• Program Memory Size: 64 KB
• Program Memory Type: Flash
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

COM0
COM1
COM2
COM3
Note: P0, P1, … Represent the pixel/segment numbers on the LCD.
A charge pump suitable for driving VLCD is included on-chip. This circuit creates 5V from the 3.3V supply. A contrast DAC is
provided that permits the LCD full-scale voltage to be adjusted between VLCD and 70% of VLCD. The LCD_NUM register
defines the number of dual purpose pins used for LCD segment interface.
LCD Voltage Boost Circuitry
A voltage boost circuit may be used to generate 5V from the 3.3V supply to support low-power 5V devices, such as LCDs.
Figure 10 shows a block diagram of the voltage boost circuitry including the voltage regulators for V2P5 and V2P5NV. When
activated using the I/O RAM register LCD_BSTEN (0x2020[7]), the boost circuitry provides an AC voltage at the VDRV output
pin (see the Applications section for details).
UART (UART0) and Optical Port (UART1)
The 71M6511/6511H includes an interface to implement an IR or optical port. The pin OPT_TX is designed to directly drive an
external LED for transmitting data on an optical link (low-active). The pin OPT_RX, also low-active, is designed to sense the
input from an external photo detector used as the receiver for the optical link. These two pins are connected to a dedicated
UART port. OPT_TX can be tristated if it is desired to multiplex another I/O pin to the OPT_TX output. The control bit for the
OPT_TX output is the I/O RAM register OPT_TXDIS (0x2008[5]).
Page: 41 of 98
A Maxim Integrated Products Brand
SEG0
P0
P1
P2
P3
Dedicated Segment Pins
SEG1
P4
P5
P6
P7
…
…
…
…
…
Table 56: Liquid Crystal Display Segment Table (Typical)
SEG19
© 2005–2010 Teridian Semiconductor Corporation
P76
P77
P78
P79
Figure 10: LCD Voltage Boost Circuitry
SEG24
Shared w/ DIO4-DIO11
V2P5NV
P80
P81
P82
P83
LCD_IBST
LCD_BSTEN
VOLTAGE
BOOST
VOLT
REG
0.1V
GNDD
…
…
…
…
…
V3P3D
V2P5
SEG31
P108
P109
P110
P111
Single-Phase Energy Meter IC
VDRV
V3P3D
VBAT
GNDD
GNDD
V2P5
VLCD
GNDD
SEG34
Shared w/ DIO14-DIO17
P112
P113
P114
P115
71M6511/71M6511H
DATA SHEET
…
…
…
…
...
SEG37
P124
P125
P126
P127
NOVEMBER 2010
V2.7