EVAL-ADM1066LFEBZ Analog Devices Inc, EVAL-ADM1066LFEBZ Datasheet
![BOARD EVALUATION FOR ADM1066LF](/photos/9/8/90849/eval-adm1066lfeb_board_sml.jpg)
EVAL-ADM1066LFEBZ
Specifications of EVAL-ADM1066LFEBZ
Related parts for EVAL-ADM1066LFEBZ
EVAL-ADM1066LFEBZ Summary of contents
Page 1
... This cable connects the main evaluation board to a standard PC USB port. Power for the evaluation board will also be provided by the PC USB interface. Order codes for evaluation kits are shown on this table (Pinouts and detailed package drawings can be found in the individual product datasheets): Rev ...
Page 2
... Ordering and SUPPORT........................................................4 CONFIGURATION TOOL ...................................................4 ADM106x EVAL BOARD HARDWARE ............................5 Eval Board Manual Switches ................................................5 Powering the ADM106x Evaluation board............................6 Communicating with the ADM106x Evaluation board .........6 ADM106x CONFIGURATION TOOL ..................................15 Introduction .........................................................................15 Installing the adm106x Software .........................................15 Uninstalling the adm106x Software ....................................16 Manually Uninstalling the adm106x software.....................16 Communicating for the FIrst Time ...
Page 3
... FET 1% Drivers FET 1% Drivers FET 1% Drivers FET 1% Drivers FET 1% Drivers FET 1% Drivers FET Drivers FET Drivers) 1% Rev. PrB | Page EVAL-ADM106x Margining Temp Sensing Yes Yes Yes 40 LFCSP/ Yes Yes 40 LFCSP/ 1 Yes Yes 40 LFCSP/ Yes 40 LFCSP/ 2 Yes 40 LFCSP/ 40 LFCSP/ Yes Yes ...
Page 4
... The configuration tool zip file can be downloaded from this webpage. The contents of this file should be extracted once downloaded. The setup.exe can then be run. Please follow this on-screen instructions to install the tool. Note that this tool is required to program and evaluate the ADM1062-69 devices. Order Code Rev. PrB | Page Preliminary Technical Data sequencing@analog ...
Page 5
... XXXXX A1 A0. A1 and A0 are pins on the device, allowing up to four ADM106x’ connected to the same SMBus. The manual switch on the Eval board allows any one of these four addresses to be set. The table below shows the effect of settings these switches ...
Page 6
... Evaluation board and the host PC, but an external 9V supply will also need to be connected. The Evaluation board can be connected to the host PC by the 3- pin header (J7) which can be connected to the parallel port using the cable provided. In such circumstances external power will need to be supplied to the board using either a 9V ...
Page 7
... Preliminary Technical Data Figure 3. ADM106x Eval Board- Block Diagram Rev. PrB | Page EVAL-ADM106x ...
Page 8
... EVAL-ADM106x Figure 4. ADM106x Eval Board Schematic- ADM106x circuitry Rev. PrB | Page Preliminary Technical Data ...
Page 9
... Preliminary Technical Data Figure 5. ADM106x Eval Board Schematic- ADM106x PDO Output circuitry EVAL-ADM106x Rev. PrB | Page ...
Page 10
... EVAL-ADM106x Figure 6. ADM106x Eval Board Schematic- Programmable Input Voltage circuitry Preliminary Technical Data Rev. PrB | Page ...
Page 11
... Preliminary Technical Data Figure 7. ADM106x Eval Board Schematic- Board Control FPGA Circuitry Rev. PrB | Page EVAL-ADM106x ...
Page 12
... EVAL-ADM106x Figure 8. ADM106x Eval Board Schematic- Board Power Supply and USB Interface Circuitry Preliminary Technical Data Rev. PrB | Page ...
Page 13
... Preliminary Technical Data Figure 9. ADM106x Eval Board Schematic- Board Voltage Measurement Circuitry Rev. PrB | Page EVAL-ADM106x ...
Page 14
... EVAL-ADM106x Figure 10. ADM106x Eval Board Silkscreen Rev. PrB | Page Preliminary Technical Data ...
Page 15
... Tool provided by Analog Devices enables the user to program the many features of these Super Sequencers through an intuitive, GUI based interface. The Eval board then allows the user to verify their configuration before usi the ADM106x in their own system application. All of the circuitry provided on the board extra to the ADM106x can also be controlled using the same software provided ...
Page 16
... Click on Control Panel 3. Click on Add or Remove Programs. The following window will appear:- Figure17. ADM106x Eval SW- Using Control Panel to uninstall 4. Highlight the ADM106x program and click on Remove to uninstall it. COMMUNICATING FOR THE FIRST TIME When first launched windows will not recognize the external Evaluation Board and will begin installing drivers automatically ...
Page 17
... Start> All Programs> ADM106x Configuration Software> ADM106x Configuration Software> Once launched, one of two windows appear. The first, if the Eval board is powered up and an ADM106x is in the socket, is shown below. The highlighted address with the tick in the box, indicates that an ADM1066 has responded on the SMBus at address 01101110 (6Eh) Figure21 ...
Page 18
... Click YES> in the dialog box above to operate the software in offline mode. Clicking NO> will close the software. The user can then power up an Evaluation board with an ADM106x inserted in its socket and restart the software. Once YES> is clicked, the window shown in Figure 23 appears:- Figure 23 ...
Page 19
... MULTIPLE DEVICE SESSION It may be required to use a number of devices simultaneously. Although this is not possible with the main evaluation board it is possible to cascade a number of Micro-Evaluation Boards together (see table 4 on page 4). When using devices in this manner over the SMBus it is important to set each device with a different address ...
Page 20
... EVAL-ADM106x . Figure 28 four ADM1069 devices at addresses and 9E As with working in offline mode devices can be toggled using the device select drop-down menu in the Top level. When another device is selected none of the other devices on the SMBus are reset. This allows the user to program one device and allow this to run while using the configuration tool to interact with another device ...
Page 21
... Any one of the ten inputs (eight for ADM1068/9) can be selected by left clicking in the drop down box shown below. Once selected, all of the functions altered in the window effect only the selected input. To configure another input simply select another one from the drop down box:- Rev. PrB | Page EVAL-ADM106x ...
Page 22
... EVAL-ADM106x Use the drop down box to select an input to configure Figure 35. Selecting an Input SELECTING A FAULT TYPE One of three fault types can be selected for each input:- 1. Under-voltage:- the input must fall below the programmed threshold before a reset is generated 2. Over-voltage:- the input must rise above the programmed threshold before a reset is generated 3 ...
Page 23
... Implementing such glitch filtering in software avoids the need for filtering capacitors in hardware. The delay can be selected from a dropdown menu by the user with delays of 0, 5µS, 10µS, 20µS, 30µS, 50µS, 75µS and Rev. PrB | Page EVAL-ADM106x ...
Page 24
... EVAL-ADM106x 100µS available. THE VX PINS AS DIGITAL INPUTS VX1-5 have dual functionality. As analog inputs, they can be programmed as described above. The only difference to the VP/VH inputs is that there is only one range to be selected and offer a true high impedance input. VX1-5 can also be programmed as digital inputs and these digital inputs are CMOS/TTL compatible ...
Page 25
... Timeout- This provides a safety net if an End-of Step Rev. PrB | Page EVAL-ADM106x FET Driver Pull-up to VP1,VP2, VP3,VP4 or VDDCAP STATE Timeout End-of-Step ...
Page 26
... EVAL-ADM106x fails to occur. The user can set a time limit on how long it can take for the End-of Step to occur. If the event does not happen, then the user can take the decision to take some remedial action (e.g supply fails to come into tolerance after 100ms likely that there is a fault on that supply and the user may wish to shut all supplies down ...
Page 27
... Figure 51. Programming the Monitor Function Programming the Monitor function can also be done independently of the Sequence or Timeout function. For instance, once a power up sequence is completed, the user may Rev. PrB | Page EVAL-ADM106x Unconditional timeout Click to enable Select Hi/Lo or OK/FLT using these monitor drop down boxes. N.B. Fault(FLT ...
Page 28
... EVAL-ADM106x only be interested in taking action if a supply subsequently fails. In this case, only the Monitor function needs to be programmed. EXPANDING THE SEQUENCE SCREEN In most applications the sequencing engine program will become long and complex. To view the program in full screen click the up/down arrow icon left of the ‘sequencing engine program’ title to expand/shrink the program window ...
Page 29
... Delete a State- Because deleting a state may affect other states (Due to it referring to other states, or other states referring to it), a dialog box containing a report of the affected states as shown in figure 59is generated by the software. Rev. PrB | Page EVAL-ADM106x ...
Page 30
... This name can of course be changed to anything although using the date and time makes retrieval of different versions of a program easier. Once a name and directory for the file have been chosen the entire SE program is saved to an Excel file, divided into fields called State, Output, Sequence, Timeout and Monitor as shown in figure 62 ...
Page 31
... If the user is concerned about noise on the input channel being measured, the Averaging function can be turned on by clicking the tick box. When enabled, the ADC will perform 16 consecutive measurements on a channel before returning the mean average value of these measurements. Rev. PrB | Page EVAL-ADM106x ...
Page 32
... EVAL-ADM106x WARNINGS The WARNINGS function is a wide OR gate which is available as an input to the Sequencing Engine and can be used as condition to move out of a State. The inputs to this OR gate are the status of the secondary voltage detectors on VP1-4/VH and the status of the ADC readings relative to their limit registers. ...
Page 33
... When the limit has been reached the software will continue to monitor the target voltage against the actual voltage. Any drift due to temperature or load will be detected and the software will adjust the DAC accordingly. Rev. PrB | Page EVAL-ADM106x Margining button DAC on button ...
Page 34
... The inputs of the ADM106x have a number of functions. The VX pins can be used as either analog or digital inputs. The VH and VPn pins can be used to look at an LDO output or at, say, the source side of a FET. The ADM106x evaluation board can be set up to provide all of these stimuli to the ADM106x. Rev. PrB | Page ...
Page 35
... This input is provided at VX5 and the user is able to add external resistors using the place holders provided. The location of these resistors on the Evaluation board is at the lower edge and are labeled R113, R60 and R59. In addition to this hardware facility there is also a software calculator provided ...
Page 36
... Clear chart:- This function clears the chart history. XY Grid ON/OFF:- This will turn the grid on or off. Reset Y axis to default:- This will reset the Y axis to display 0 – 15V Calibrate Evaluation Board:- This function will launch a program as shown in figure 75 which will individually calibrate the 72 onboard power supplies to +/- 1% accuracy. ...
Page 37
... There are four buttons that may be selected in this window . Figure 79. Save settings to file window 1. Save eval board settings:- This option will save the evaluation board configuration to file for the inputs to the device only. 2. Save controlling registers:- This option will save all the configuration register data to file ...
Page 38
... There are three buttons that may be selected in this window . Figure 83. Recall settings from file window 1. Recall eval board settings:- This option will recall the evaluation board configuration from file for the inputs to the device only. ...