AMMC-6420-W50 Avago Technologies US Inc., AMMC-6420-W50 Datasheet
![IC MMIC 1W POWER AMP 6-18GHZ](/photos/30/99/309977/ammc-group_wht_sml.jpg)
AMMC-6420-W50
Specifications of AMMC-6420-W50
Related parts for AMMC-6420-W50
AMMC-6420-W50 Summary of contents
Page 1
... Power: @17 GHz, P-2dB=30.5 dBm • Highly linear: OIP3=38dBm • Integrated RF power detector • 5.5 Volt, -0.6 Volt, 800mA operation Applications • Microwave Radio systems • Satellite VSAT and DBS systems • LMDS & Pt-Pt mmW Long Haul • 802.16 & 802.20 WiMax BWA • WLL and MMDS loops • Can be driven by AMMC-5618 (6-20 GHz) MMIC increasing luding overall gain. [1] Units dBm °C °C ° ...
Page 2
... AMMC-6420 DC Specifications/Physical Properties Symbol Parameters and Test Conditions I Drain Supply Current d (under any RF power drive and temperature set for Gate Supply Operating Voltage 800 (mA)) d(Q) q Thermal Resistance [2] ch-b (Backside temperature, T Notes: 1. Ambient operational temperature T =25°C unless otherwise noted Channel-to-backside Thermal Resistance (θ tance at backside temperature ( 25°C calculated from measured data AMMC-6420 RF Specifications (T Symbol Parameters and Test Conditions [4] Gain Small-signal Gain P Output Power at 1dB -1dB Gain Compression ...
Page 3
... AMMC-6420 Typical Performances (T = 25° NOTE: These measurements are Ω test environment. Aspects of the amplifier performance may be improved over a more narrow bandwidth by application of additional conjugate, linearity, or power matching S1[dB] S1[dB Frequency [GHz] Figure 1. Typical Gain and Reverse Isolation Frequency [GHz] Figure 4. Typical Noise Figure 0 - -10 -1 -0 S11_0 S11_-0 S11_8 - Frequency [GHz] Figure 7 ...
Page 4
P-_8deg P-_0deg P-_-0deg Frequency [GHz] Figure 10. Typical P-2 over temperature [1] Typical Scattering Parameters , (T = 25° S11 Freq GHz dB Mag Phase 1 -0.85 ...
Page 5
Biasing and Operation The recommended quiescent DC bias condition for optimum efficiency, performance, and reliability is Vd=5.5 volts with Vg set for Id=800 mA. Minor improvements in performance are possible depending on the application. The drain bias voltage range 5.5V. A single DC gate supply connected to Vg will bias all gain stages. Muting can be accomplished by setting Vg to the pinch-off voltage Vp (-1.0V). An optional output power detector network is also provided. The differential voltage between the Det-Ref ...
Page 6
... Figure 11. AMMC-6420 Schematic RF in Figure 12. AMMC-6420 Bonding pad locations DET DET out RF out ...
Page 7
... Figure 13. AMMC-6420 Assembly diagram 0.45 0.40 0.35 0.30 0.25 0.20 0.15 0.10 0. Pout[dBm] Figure 14. AMMC-6420 Typical Detector Voltage and Output Power, Freq=12GHz DET _ O RFOutput RFO DET Notes: =>1mF capacitors on DC biasing lines not 1. shown required. Vg connections recommended on both 2. sides for devices operating at or above 1 condition ...
Page 8
... Ordering Information: AMMC-6420-W10 = 10 devices per tray AMMC-6420-W50 = 50 devices per tray For product information and a complete list of distributors, please go to our web site: Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies in the United States and other countries. Data subject to change. Copyright © 2005-2008 Avago Technologies. All rights reserved. Obsoletes AV01-0219EN AV02-1370EN - September 4, 2008 www ...