ISL5829IN Intersil, ISL5829IN Datasheet - Page 11
![no-image](/images/manufacturer_photos/0/3/341/intersil_sml.jpg)
ISL5829IN
Manufacturer Part Number
ISL5829IN
Description
IC DAC DUAL 12BIT 3.3V 48-MQFP
Manufacturer
Intersil
Datasheet
1.ISL5829EVAL1.pdf
(13 pages)
Specifications of ISL5829IN
Function
D/A Converter
Frequency
130MHz
Rf Type
GSM, EDGE, CDMA2000, WCMDA, TDS-CDMA
Secondary Attributes
Dual 12-Bit
Package / Case
48-LQFP
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
reflections, proper termination should be implemented. If the
lines driving the clock and the digital inputs are long 50Ω
lines, then 50Ω termination resistors should be placed as
close to the converter inputs as possible connected to the
digital ground plane (if separate grounds are used). These
termination resistors are not likely needed as long as the
digital waveform source is within a few inches of the DAC.
For pattern drivers with very high speed edge rates, it is
recommended that the user consider series termination (50-
200Ω) prior to the DAC’s inputs in order to reduce the
amount of noise.
Power Supply
Separate digital and analog power supplies are
recommended. The allowable supply range is +2.7V to
+3.6V. The recommended supply range is +3.0 to 3.6V
(nominally +3.3V) to maintain optimum SFDR. However,
operation down to +2.7V is possible with some degradation
in SFDR. Reducing the analog output current can help the
SFDR at +2.7V. The SFDR values stated in the table of
specifications were obtained with a +3.3V supply.
Ground Planes
Separate digital and analog ground planes should be used.
All of the digital functions of the device and their
corresponding components should be located over the
digital ground plane and terminated to the digital ground
plane. The same is true for the analog components and the
analog ground plane.
Noise Reduction
To minimize power supply noise, 0.1µF capacitors should be
placed as close as possible to the converter’s power supply
pins, AV
using separate digital and analog ground planes and these
capacitors should be terminated to the digital ground for
DV
of the power supplies on the board is recommended.
Voltage Reference
The internal voltage reference of the device has a nominal
value of +1.23V with a ±40ppm/°C drift coefficient over the
full temperature range of the converter. It is recommended
that a 0.1µF capacitor be placed as close as possible to the
REFIO pin, connected to the analog ground. The REFLO pin
selects the reference. The internal reference can be selected
if REFLO is tied low (ground). If an external reference is
desired, then REFLO should be tied high (the analog supply
voltage) and the external reference driven into REFIO. The
full scale output current of the converter is a function of the
voltage reference used and the value of R
be within the 2mA to 22mA range, though operation below
2mA is possible, with performance degradation.
If the internal reference is used, V
approximately 1.2V. If an external reference is used, V
DD
and to the analog ground for AV
DD
and DV
DD
. Also, the layout should be designed
11
FSADJ
DD
. Additional filtering
will equal
SET
. I
OUT
should
FSADJ
ISL5829
will equal the external reference. The calculation for I
(Full Scale) is:
I
If the full scale output current is set to 20mA by using the
internal voltage reference (1.23V) and a 1.91kΩ R
resistor, then the input coding to output current will resemble
the following:
Analog Output
IOUTA and IOUTB are complementary current outputs. The
sum of the two currents is always equal to the full scale
output current minus one LSB. If single ended use is
desired, a load resistor can be used to convert the output
current to a voltage. It is recommended that the unused
output be either grounded or equally terminated. The voltage
developed at the output must not violate the output voltage
compliance range of -1.0V to 1.25V. R
loading each current output) should be chosen so that the
desired output voltage is produced in conjunction with the
output full scale current. If a known line impedance is to be
driven, then the output load resistor should be chosen to
match this impedance. The output voltage equation is:
V
The most effective method for reducing the power
consumption is to reduce the analog output current, which
dominates the supply current. The maximum recommended
output current is 20mA.
Differential Output
IOUTA and IOUTB can be used in a differential-to-single-
ended arrangement to achieve better harmonic rejection.
With R
will provide a 500mV (-2.5dBm) signal at the output of the
transformer if the full scale output current of the DAC is set to
20mA (used for the electrical specifications table). Values of
R
performance curves to increase the output power and the
dynamic range. The center tap in Figure 13 must be
grounded.
In the circuit in Figure 14, the user is left with the option to
ground or float the center tap. The DC voltage that will exist
at either IOUTA or IOUTB if the center tap is floating is
IOUT
transformer. If the center tap is grounded, the DC voltage is
0V. Recommended values for the circuit in Figure 14 are
OUT
INPUT CODE (D11-D0)
OUT
DIFF
TABLE 1. INPUT CODING vs OUTPUT CURRENT WITH
1111 1111 1111
1000 0000 0000
0000 0000 0000
(Full Scale) = (V
DC
= 100Ω and R
= I
DIFF
OUT
x (R
= 50Ω and R
INTERNAL REFERENCE (1.23V TYP) AND
RSET=1.91KΩ
A
X R
//R
B
OUT
) V because R
LOAD
FSADJ
.
LOAD
=50Ω were used for the typical
IOUTA (mA)
/R
=50Ω, the circuit in Figure 13
SET)
20.6
10.3
0
DIFF
X 32.
OUT
is DC shorted by the
(the impedance
IOUTB (mA)
10.3
20.6
SET
0
OUT