X24-019PKC-RA Digi International/Maxstream, X24-019PKC-RA Datasheet - Page 31
![no-image](/images/no-image-200.jpg)
X24-019PKC-RA
Manufacturer Part Number
X24-019PKC-RA
Description
MOD RF 2.4GHZ 19.2K RS232/485
Manufacturer
Digi International/Maxstream
Series
XStream™r
Specifications of X24-019PKC-RA
Function
Transceiver, Modem
Modulation Or Protocol
FHSS
Frequency
2.4GHz ~ 2.4835GHz
Applications
General Purpose
Interface
RS-232, RS-485
Sensitivity
-102dBm
Power - Output
17dBm (50mW)
Data Rate - Maximum
20 kbps
Voltage - Supply
5V
Package / Case
Module
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Features
-
© 2006 MaxStream, Inc. Confidential & Proprietary
XStream‐PKG‐R™ RS‐232/485 RF Modem – Product Manual v5.x00 [2006.02.24]
HT (Time before Wake-up Initializer) Command
ID (Modem VID) Command
IU (DI2, DI3 Update Timer) Command
<<Sleep (Low Power)> If any modems within
range are running in a “Cyclic Sleep” setting, a
wake-up initializer must be used by the
transmitting modem for sleeping modems to
remain awake [refer to the LH (“Wake-up
Initializer Timer”) Command]. When a receiving
modem in Cyclic Sleep wakes, it must detect the
wake-up initializer in order to remain awake and
receive data. The value of HT Parameter tells the
transmitter, “After a period of inactivity (no
transmitting or receiving) lasting HT amount of
time, send a long wake-up initializer”. HT
Parameter should be set to match the inactivity timeout [specified by ST (Time before Sleep)
command] used by the receiver(s).
From the receiving modem perspective, after HT time elapses and the inactivity timeout [ST
command] is met, the receiver goes into cyclic sleep. In cyclic sleep, the receiver wakes once per
sleep interval to check for a wake-up initializer. When a wake-up initializer is detected, the
modem will stay awake to receive data. The wake-up initializer must be longer than the cyclic
sleep interval to ensure that sleeping modems detect incoming data. When HT time elapses, the
transmitter then knows that it needs to send a long Wake-up Initializer for all receivers to be able
to remain awake and receive the next transmission. Matching HT to the time specified by ST on
the receiving modem guarantees that all receivers will detect the next transmission.
<Networking> Set/Read the “Vendor
Identification Number”. Only modems with
matching IDs can communicate with each other.
Modems with non-matching VIDs will not receive
unintended data transmission.
<Serial Interfacing> Set/Read the interval at
which the status of DI2, DI3 and Break is
transmitted. Additionally, status is transmitted
whenever there is a transition. A setting of “0”
disables periodic update. DI2 or DI3 passing
must be enabled for the update to take place.
AT Command: ATIU
Binary Command: 0x3B (59 decimal)
Parameter Range: 0 - 0xFFFF [x 100 ms]
Default Parameter Value: 0x0A (10 decimal)
Number of bytes returned: 2
Related Commands: BK (Serial Break Passing),
BO (Serial Break Timeout), CO (DO3 Timeout),
DR (Disconnect), RT (DI2 Configuration), TO
(DO2 Timeout)
Minimum Firmware Version Required: 4.30
AT Command: ATHT
Binary Command: 0x03 (3 decimal)
Parameter Range: 0 – 0xFFFF
Default Parameter Value: 0xFFFF (means that
long wake-up initializer will not be sent)
Number of bytes returned: 2
Related Commands: LH (Wake-up Initializer
Timer), SM (Sleep Mode), ST (Time before
Sleep)
AT Command: ATID
Binary Command: 0x27 (39 decimal)
Parameter Range (user-settable):
(Factory-set and read-only) :
Number of bytes returned: 2
Minimum Firmware Version Required: 4.2B
(Previous versions did not support user-
settable VIDs)
0x10 - 0x7FFFF
0x8000 – 0xFFFF
[x 100 milliseconds]
31