ATMEGA256RZAV-8AU Atmel, ATMEGA256RZAV-8AU Datasheet - Page 12

• Manufacturer Part Number: ATMEGA256RZAV-8AU
• Description: MCU ATMEGA2561/AT86RF230 64-TQFP
• Manufacturer: Atmel
• Series: ATMEGAr

Specifications of ATMEGA256RZAV-8AU

• Frequency: 2.4GHz
• Modulation Or Protocol: 802.15.4 Zigbee
• Applications: ISM, ZigBee™
• Power - Output: 3dBm
• Sensitivity: -101dBm
• Voltage - Supply: 1.8 V ~ 3.6 V
• Current - Receiving: 15.5mA
• Current - Transmitting: 16.5mA
• Data Interface: PCB, Surface Mount
• Memory Size: 256kB Flash, 4kB EEPROM, 8kB RAM
• Antenna Connector: PCB, Surface Mount
• Package / Case: 64-TQFP
• Wireless Frequency: 2.4 GHz
• Interface Type: JTAG, SPI
• Output Power: 3 dBm
• For Use With: ATAVRISP2 - PROGRAMMER AVR IN SYSTEM
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Operating Temperature: -
• Data Rate - Maximum: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• For Use With/related Products: ATmega256

6.2 SPI Protocol
Table 6-2. SPI Command Byte Definition
6.2.1 Register Access Mode
12
Bit 7
1
1
0
0
0
0
AT86RF230
Bit 6
0
1
0
1
0
1
Bit 5
1
1
0
0
Bit 4
master device or an external pull-up resistor. Note, when both SEL and RST are
active, the MISO output driver is also enabled.
The MOSI line is sampled by the radio transceiver at the rising edge of SCLK. The
signal must be stable before and after the rising edge of SCLK as specified by t
refer to section 11.4 parameters 11.4.5 and 11.4.6.
This mode of SPI operation is commonly called “SPI Mode 0”.
Each transfer sequence starts with transferring a command byte from SPI master via
MOSI (see Table 6-2) with MSB first. This command byte defines the access mode and
additional mode-dependent information.
The different access modes are described within the following sections.
In Figure 6-4 to Figure 6-14 logic values stated with X on MOSI are ignored by the radio
transceiver, but need to have a valid level. Return values on MISO stated as X shall be
ignored by the microcontroller.
The Register access mode is a two-byte read/write operation and is initiated by setting
register access (see Table 6-2) and a register address (see Table 12-1).
On write access the second byte transferred on MOSI contains the write data to the
selected address (see Figure 6-4).
Figure 6-4. Packet Structure – Register Write Access
On read access the content of the selected register address is returned in the second
byte on MISO (see Figure 6-5).
SEL = L. The first transferred byte on MOSI is the command byte and must indicate a
MOSI
MISO
Register address [5:0]
Register address [5:0]
Bit 3
1
byte 1 (command byte)
1
Reserved
Reserved
Reserved
Reserved
Bit 2
address[5:0]
XX
Bit 1
Bit 0
write data[7:0]
byte 2 (data byte)
XX
Mode
Register Access Mode – Read Access
Register Access Mode – Write Access
Frame Buffer Access Mode – Read Access
Frame Buffer Access Mode – Write Access
SRAM Access Mode – Read Access
SRAM Access Mode – Write Access
5131E-MCU Wireless-02/09
3
and t
4
,