ZFSM-201-1C CEL, ZFSM-201-1C Datasheet - Page 6
![MODULE ZIG 802.15.4 W/MMCX CONN](/photos/14/20/142074/zfsm-201-1c_sml.jpg)
ZFSM-201-1C
Manufacturer Part Number
ZFSM-201-1C
Description
MODULE ZIG 802.15.4 W/MMCX CONN
Manufacturer
CEL
Series
FreeStar Pror
Datasheet
1.ZFSM-201-1.pdf
(17 pages)
Specifications of ZFSM-201-1C
Frequency
2.4GHz
Data Rate - Maximum
250kbps
Modulation Or Protocol
802.15.4 Zigbee
Applications
Home/Building Automation, Industrial Control and Monitoring
Power - Output
20dBm
Sensitivity
-94dBm
Voltage - Supply
2.1 V ~ 3.6 V
Current - Receiving
30mA
Current - Transmitting
193mA
Data Interface
Pads for Pins
Memory Size
128kB Flash, 96kB RAM, 80kB ROM
Antenna Connector
MMCX
Operating Temperature
-40°C ~ 85°C
Package / Case
Module
Wireless Frequency
2.4 GHz
Security
128 bit AES
Operating Voltage
2.1 V to 3.6 V
Output Power
100 mW
Antenna
MMCX
Operating Temperature Range
- 40 C to + 85 C
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With/related Products
MC13224V
POWER AMPLIFIER
The FreeStar Pro module incorporates a high performance Power Amplifier from NEC Electronics.
Power Amplifier Control Line
FreeStar Pro modules include a separate 1.8V regulator supplying a bias that enables consistent module output performance
over the wide operating range. To prevent excessive sleep current draw, this regulator should be disabled when the module is
placed into sleep mode.The voltage regulator is controlled by GPIO42 (ANT1), setting GPIO42 high enables the regulator while
setting GPIO42 low disables the regulator. See the table below for the Turn on Time requirements for the voltage regulator.
SPECIFICATIONS — GPIO42
For the TX_ON and RX_ON pins, the function table is as follows:
Other Notes:
RF Output Power Setting
In order to comply with FCC emissions requirements, the FreeStar PRO module must operate at reduced power settings
on channels 11 & 12. Channel 26 is unavailable. The firmware provided with the modules also limits the users to Test Tool
power step 2 for channels 11 & 12. This is to guarantee the module does not exceed 10dBm which is required to meet the
FCC requirements of this module.
In addition to restricting power, the firmware also limits the maximum data payload to 106 bytes for any transmitted packet.
This is to guarantee the module does not exceed 10dBm on channels 11 & 12 which is necessary to meet FCC emissions
requirements.
INTERFACE
The FreeStar Pro module has all major pins routed to the castellation connectors, this includes, but is not limited, to the pins for
JTAG, serial communication, A/D, etc.
Parameter
Regulator enable voltage
Regulator disable voltage
Turn on Time for V
Parameter
TX_ON
RX_ON
• The GPIO43 (ANT2) pin is not used and is left unconnected.
• Due to the long turn on time (105µs) of the regulator, the regulator is enabled or ON all the time with the
• The RF switch uses both the TX_ON and RX_ON outputs as control inputs.
• The PA uses the TX_ON line as the control input.
execption of sleep mode.
OUT
=1.8V (Default)
TX Mode
Min
High
Low
Typ
0.95
0.40
105
Page 6
Max
200
RX Mode
High
Low
µsec
Unit
V
V
ZFSM-201 Series