XBP24-PKI-001-RA Digi International/Maxstream, XBP24-PKI-001-RA Datasheet - Page 45

• Manufacturer Part Number: XBP24-PKI-001-RA
• Description: MODULE 802.15.4 RS-232 ANT
• Manufacturer: Digi International/Maxstream
• Series: XBEE-PRO™r

Specifications of XBP24-PKI-001-RA

• Frequency: 2.4GHz
• Data Rate - Maximum: 250kbps
• Modulation Or Protocol: 802.15.4
• Applications: Home/Building Automation, Industrial Control, ZigBee™
• Power - Output: 0dBm
• Sensitivity: -92dBm
• Voltage - Supply: 2.8 V ~ 3.4 V
• Current - Receiving: 55mA
• Data Interface: Connector, Female DB-9
• Antenna Connector: RP-SMA
• Operating Temperature: -40°C ~ 85°C
• Package / Case: Module
• Memory Size: -
• Current - Transmitting: -
• Other names: Q3255595

© 2008 Digi International, Inc.
XBee‐PRO PKG‐R® RS‐232 RF Modem – 802.15.4 ‐ Product Manual v1.xAx
PL (Power Level) Command
PR (Pull-up Resistor Enable) Command
PT (PWM Output Timeout) Command
RE (Restore Defaults) Command
<RF Interfacing> The PL command is used to
select and read the power level at which the RF
modem transmits conducted power.
WHEN OPERATING IN EUROPE:
XBee-PRO RF Modems must be configured to
operate at a maximum transmit power output
level of 10 dBm. The PL parameter must equal
“0” (10 dBm).
Additionally, European regulations stipulate an
EIRP power maximum of 12.86 dBm (19 mW) for
the XBee-PRO and 12.11 dBm for the XBee when
integrating high-gain antennas.
WHEN OPERATING IN JAPAN:
XBee-PRO RF Modems optimized for use in Japan contain firmware that limits transmit power
output to 10 dBm. If PL=4 (default), the maximum power output level is 10 dBm.
<Serial Interfacing> The PR command is used to
set and read the bit field that is used to configure
internal the pull-up resistor status for I/O lines.
“1” specifies the pull-up resistor is enabled. “0”
specifies no pull up.
For example: Sending the command “ATPR 6F” will turn bits 0, 1, 2, 3, 5 and 6 ON; and bits 4 & 7
will be turned OFF. (The binary equivalent of “0x6F” is “01101111”. Note that ‘bit 0’ is the last
digit in the bitfield.
<I/O Settings {I/O Line Passing}> The PT
command is used to set/read the output timeout
value for both PWM outputs.
When PWM is set to a non-zero value: Due to I/O
line passing, a time is started which when expired
will set the PWM output to zero. The timer is reset
when a valid I/O packet is received.
<(Special)> The RE command is used to restore
all configurable parameters to their factory
default settings. The RE command does not write
restored values to non-volatile (persistent) memory. Issue the WR (Write) command subsequent
to issuing the RE command to save restored parameter values to non-volatile memory.
bit 0 - AD4/DIO4 (pin 11)
bit 1 - AD3/DIO3 (pin 17)
bit 2 - AD2/DIO2 (pin 18)
bit 3 - AD1/DIO1 (pin 19)
bit 4 - AD0/DIO0 (pin 20)
bit 5 - AD6/DIO6 (pin 16)
bit 6 - DI8 (pin 9)
bit 7 - DIN/CONFIG (pin 3)
AT Command: ATRE
AT Command: ATPL
Parameter Range: 0 - 4
Default Parameter Value: 4
AT Command: ATPR
Parameter Range: 0 - 0xFF
Default Parameter Value: 0xFF
(all pull-up resistors are enabled)
Minimum Firmware Version Required: v1.x80
AT Command: ATPT
Parameter Range: 0 - 0xFF [x 100 msec]
Default Parameter Value: 0xFF
Minimum Firmware Version Required: 1.xA0
Parameter
0
1
2
3
4
-10 dBm
-6 dBm
-4 dBm
-2 dBm
0 dBm
XBee
XBee-PRO
10 dBm
12 dBm
14 dBm
16 dBm
18 dBm
45