ZB2430-Q-C-X-U Laird Technologies, ZB2430-Q-C-X-U Datasheet - Page 43

• Manufacturer Part Number: ZB2430-Q-C-X-U
• Description: MOD ANT CONN ZIGBEE 2-100MW U.FL
• Manufacturer: Laird Technologies
• Series: AeroCommr

Specifications of ZB2430-Q-C-X-U

• Frequency: 2.4GHz
• Data Rate - Maximum: 250kbps
• Modulation Or Protocol: 802.15.4 Zigbee
• Applications: AMR, ISM, Security and Access
• Power - Output: 10dBm ~ 20dBm
• Sensitivity: -99dBm
• Voltage - Supply: 3 V ~ 3.5 V
• Current - Receiving: 27mA
• Current - Transmitting: 25mA
• Data Interface: PCB, Through Hole
• Antenna Connector: U.FL
• Operating Temperature: -40°C ~ 85°C
• Package / Case: Module
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Memory Size: -

3 8
E E P R O M P A R A M E T E R S
Broadcast Attempts
End-to-End Retries
Network Retries
Parameter
MAC Retries
Baud Rate
Control 0
Baud_M
Baud_E
EEPROM
Address
0x4B
0x4C
0x4D
0x4E
0x42
0x43
0x44
0x45
Ta b l e 9 : E E P R O M P a r a m e t e r s
(Bytes)
Length
1
1
1
1
1
1
1
1
0x00 - 0x08, 0xE3
0x00 - 0xFF
0x01 - 0xFF
0x00 - 0x07
0x01 - 0x07
0x00 - 0x05
0x00 - 0xFF
0x00-0xFF
Range
Default
0xFF
0xFF
0x06
0x38
0x03
0x02
0x04
0x04
Description
0x00: 1200
0x01: 2400
0x02: 4800
0x03: 9600
0x04: 19200
0x05: 31250
0x06: 38400
0x07: 57600
0x08: 115200
0xE3: Enable Custom Baud rate
Note: If any value ofther than 0x00-0x08 or 0xE3
is used, the radio will default to 9600 baud.
Used to calculate baud rate when Custom
Baud Rate is enabled.
Used to calculate baud rate when Custom
Baud Rate is enabled.
Settings are:
bit-7: Reserved
bit-6: Reserved
bit-5: Modify Wake
bit-4: Reload Sleep
bit-3: NV Restore
bit-2: End-to-End Acknowledgement
bit-1: Reserved
bit-0: Reserved
Specifies the number of retries to use at the
MAC level. A setting of 0x03 actually sends the
packet up to 4 times. MAC retries can be set to
0x00, but since they occur faster than the trans-
mit retries, the default setting is typically recom-
mended.
Specifies the maximum number of network
retries. When MAC retries is not set to 0x00, the
actual amount of transmit attempts is equal to
MAC retries x Network Retries. Network Retries
occur at a slower rate than MAC retries. Net-
work retries are retries that occur between two
connected nodes.
Specified the maximum number of times to
broadcast a packet. Attempts occur at 500ms
intervals. There is a limit of 9 broadcast mes-
sages every 10 seconds.
Specified the maximum number of times to
retry an end to end packet. End to End Retries
are only suitable for multihop packets..
Attempts occur at 6s intervals.
0 = Disabled
1 = Enabled
0 = Disabled
1 = Enabled
0 = Disabled
1 = Enabled
0 = Disabled
1 = Enabled