CYWUSB6935-28SEI Cypress Semiconductor Corp, CYWUSB6935-28SEI Datasheet - Page 8
![no-image](/images/manufacturer_photos/0/1/179/cypress_semiconductor_corp_sml.jpg)
CYWUSB6935-28SEI
Manufacturer Part Number
CYWUSB6935-28SEI
Description
IC WIRELESS USB 2.4GHZ 28-SOIC
Manufacturer
Cypress Semiconductor Corp
Datasheet
1.CYWUSB6935-28SEI.pdf
(32 pages)
Specifications of CYWUSB6935-28SEI
Frequency
2.4GHz
Data Rate - Maximum
62.5kbps
Modulation Or Protocol
DSSS, GFSK
Applications
AMR, ISM, RKE
Power - Output
0dBm
Sensitivity
-95dBm
Voltage - Supply
2.7 V ~ 3.6 V
Current - Receiving
57.7mA
Current - Transmitting
69.1mA
Data Interface
PCB, Surface Mount
Antenna Connector
PCB, Surface Mount
Operating Temperature
-40°C ~ 85°C
Package / Case
28-SOIC
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Memory Size
-
Other names
428-1576-5
Document 38-16008 Rev. **
Bit
7:4
3:0
Bit
7:5
4:0
Bit
7
6:0
Reserved
Name
Reserved
Count
Name
7
7
Name
Reserved
Count
7
Silicon ID
Product ID
Addr: 0x00
Addr: 0x01
Addr: 0x02
Description
These bits are reserved and should be written with zeros.
The Synthesizer A Counter register is used for diagnostic purposes and is not recommended for normal operation.
The Channel register is the recommended method of setting the Synthesizer frequency.
The Synthesizer A Count along with the Synthesizer N Count can be used to generate the Synthesizer frequency. The
range of valid values of the Synthesizer A Count is 0 through 31. Using the Synthesizer A and N Count register is an
alternative to using the Channel register. Selection between the use of the Channel register or the A and N registers
is done through the Channel register (Reg 0x21, bit 7). When in Channel mode the A and N Count bits can be used
to read the A and N values derived directly from the Channel.
Description
This bit is reserved and should be written with zero.
The Synthesizer N Counter register is used for diagnostic purposes and therefore is not recommended for normal
operation. The Channel register is the recommended method of setting the Synthesizer frequency.
The Synthesizer N Count along with the Synthesizer A Count can be used to generate the Synthesizer frequency. The
range of valid values of the Synthesizer N Count is 74 through 76. Using the Synthesizer A and N Count register is
an alternative to using the Channel register. Selection between the use of the Channel register or the A and N registers
is done through the Channel register (Reg 0x21, bit 7). When in Channel mode the A and N Count bits can be used
to read the A and N values derived directly from the Channel.
Reserved
Description
These are the Silicon ID revision bits. 0000 = Rev A, 0001 = Rev B, etc. These bits are read-only.
These are the Product ID revision bits. Fixed at value 0111. These bits are read-only.
6
6
6
Silicon ID
5
5
5
Figure 7-2. Synthesizer A Counter
Figure 7-3. Synthesizer N Counter
Figure 7-1. Revision ID Register
PRELIMINARY
REG_SYN_A_CNT
REG_SYN_N_CNT
4
4
4
REG_ID
Count
3
3
3
Count
2
2
2
Product ID
1
1
1
CYWUSB6935
Default: 0x07
Default: 0x00
Default: 0x00
Page 8 of 32
0
0
0