SX1230I066TRT Semtech, SX1230I066TRT Datasheet - Page 10
![IC TX UHF 433/868/916 MHZ 24-QFN](/photos/14/23/142352/sx1230i066trt_sml.jpg)
SX1230I066TRT
Manufacturer Part Number
SX1230I066TRT
Description
IC TX UHF 433/868/916 MHZ 24-QFN
Manufacturer
Semtech
Datasheet
1.SM1230E868.pdf
(46 pages)
Specifications of SX1230I066TRT
Frequency
315MHz, 434MHz, 868MHz, 915MHz
Applications
RKE
Modulation Or Protocol
ISM
Data Rate - Maximum
600kbps
Power - Output
17dBm
Current - Transmitting
95mA
Data Interface
PCB, Surface Mount
Antenna Connector
PCB, Surface Mount
Voltage - Supply
1.8 V ~ 3.7 V
Operating Temperature
-40°C ~ 85°C
Package / Case
24-MLPQ
Operating Temperature (min)
-40C
Operating Temperature (max)
85C
Operating Temperature Classification
Industrial
Product Depth (mm)
4mm
Product Length (mm)
4mm
Operating Supply Voltage (min)
1.8V
Operating Supply Voltage (typ)
2.5/3.3V
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Features
-
Memory Size
-
Lead Free Status / Rohs Status
Supplier Unconfirmed
Other names
Q4629601
SX1230I066TR
SX1230I066TRT
SX1230I066TR
SX1230I066TRT
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
SX1230I066TRT
Manufacturer:
Semtech
Quantity:
42 000
Part Number:
SX1230I066TRT
Manufacturer:
SEMTECH/美国升特
Quantity:
20 000
4. Working Modes of the SX1230
4.1. Operating Modes
The four operating modes of the SX1230 are shown in Table 6. Each of these may be selected via the SPI bus by writing
the corresponding bits to Mode(2:0). A key feature of the SX1230 is that the transition from one operating mode to the next
is automatically optimized. For example, if the transmit operating mode is selected whilst in sleep operating mode then, in
a pre-defined time-optimized sequence, each of the intermediate modes is engaged sequentially without the need to issue
any further SPI commands. For more information on timing and optimization please see Section 7.4.
Table 6
4.2. Application Modes
The SX1230 has two application modes, selected by applying an external logical level to the E2_MODE input (pin 6). The
first, MCU mode (E2_Mode= ‘0’), configures the SX1230 as an SPI slave. This permits the configuration of the circuit by an
external microprocessor via the SPI interface of the SX1230 and the data to be applied via the DATA input (pin 14). The
second application mode, stand-alone mode (E2_Mode = 0), sees the SX1230 configured as SPI master. In the stand-
alone application mode the SX1230 can download its configuration from an external SPI E
to an input on the GPIO pins, a specific configuration can be programmed and a payload transmitted.
Note that this mode selection process is performed at start up (or POR) of the circuit. Thus the hardware mode cannot be
dynamically changed without resetting the chip. This may be achieved either by power down or by issuing an active high
POR signal to the Reset input (pin 5). For reset signal timing please see the diagram of Figure 13 and accompanying
description.
4.2.1. Stand Alone Mode
In stand alone mode (E2_Mode = ‘1’) the SX1230 will operate as a stand-alone SPI master which can download both
register settings and data payload from an SPI E
in this application mode the SX1230 remains in sleep operating mode until either a single or combination of button presses
are detected. SX1230 can then be dynamically reconfigured and / or transmit a data sequence stored within the E
The SX1230 can accommodate SPI E
description of E
circuit for stand-alone operation is shown in Figure 3, note that both matching and L
application specific.
SX1230, Revision 2 May 2009
©2008 Semtech Corp.
ADVANCED COMMUNICATIONS & SENSING
MODE(2:0)
SX1230 Operating Modes
000
001
010
011
2
PROM use with SX1230 and the associated application circuits, please see Section 6.1. The application
Sleep mode
Stand-by mode
FS mode
Transmit mode
Selected Mode
2
PROM sizes up to 8 kbit and uses industry standard SPI commands. For a full
Optional
Optional
Optional
Optional
RC Osc
2
PROM. Four debounced GPIO inputs are available in stand alone mode,
Page 10
SPI
x
x
x
x
Enabled Blocks
Xtal Osc
x
x
x
Integrated Transmitter IC
M
are band specific whilst C
2
Freq. Synth.
PROM. Moreover, in response
x
x
www.semtech.com
DATASHEET
SX1230
PA
x
2
PROM.
TX
is