XR17V352IB113-F Exar Corporation, XR17V352IB113-F Datasheet - Page 8

• Manufacturer Part Number: XR17V352IB113-F
• Description: IC UART PCIE 256B DUAL 113FPBGA
• Manufacturer: Exar Corporation

Specifications of XR17V352IB113-F

• Number Of Channels: 2, DUART
• Package / Case: 113-LFBGA
• Features: *
• Fifo's: 256 Byte
• Protocol: RS485
• Voltage - Supply: 3.3V
• With Auto Flow Control: Yes
• With Irda Encoder/decoder: Yes
• With False Start Bit Detection: Yes
• With Modem Control: Yes
• Mounting Type: Surface Mount
• Data Rate: 25 Mbps
• Supply Current: 120 mA
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Mounting Style: SMD/SMT
• Operating Supply Voltage: 3.3 V
• No. Of Channels: 2
• Uart Features: Tx/Rx FIFO Counters
• Supply Voltage Range: 3V To 3.6V
• Operating Temperature Range: -40°C To +85°C
• Digital Ic Case Style: BGA
• No. Of Pins: 113
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

XR17V352
HIGH PERFORMANCE DUAL PCI EXPRESS UART
The XR17V352 UART register set is very similar to the previous generation PCI UARTs. This makes the V352
software compatible with the previous generation PCI UARTs. Minimal changes are needed to the software
driver of an existing Exar PCI UART driver so that it can be used with the V352 PCIe UART.
There are three different sets of registers as shown in
Registers is needed for plug-and-play auto-configuration. This auto-configuration feature makes installation
very easy into a PCI system and it is part of the PCI local bus specification. The second register set is the
Device Configuration Registers that are also accessible directly from the PCI bus for programming general
operating conditions of the device and monitoring the status of various functions common to both channels.
These functions include both channel UARTs’ interrupt control and status, 16-bit general purpose timer control
and status, multipurpose inputs/outputs control and status, sleep mode, soft-reset, and device identification
and revision. And lastly, each UART channel has its own set of internal UART Configuration Registers for its
own operation control and status reporting. Both sets of channel registers are embedded inside the device
configuration registers space, which provides faster access. The second and third set of registers are mapped
into 2K of the PCI bus memory address space. The following paragraphs describe all 3 sets of registers in
detail.
The PCI local bus configuration space registers are responsible for setting up the device’s operating
environment in the PCI local bus. The pre-defined operating parameters of the device is read by the PCI bus
plug-and-play auto-configuration manager in the operating system. After the PCI bus has collected all data
from every device/card on the bus, it defines and downloads the memory mapping information to each device/
card about their individual operation memory address location and conditions. The operating memory mapped
address location is downloaded into the Base Address Register (BAR) register, located at an address offset of
0x10 in the configuration space. Custom modification of certain registers is possible by using an external
93C46 EEPROM. The EEPROM contains the device vendor and sub-vendor data, along with 6 other words of
information (see
F
1.0 XR17V352 INTERNAL REGISTERS
1.1
IGURE
Device Configuration and
Registers are mapped on
byte of memory address
UART[1:0] Configuration
Register (BAR) in a 2K-
to the Base Address
3. T
PCI LOCAL BUS CONFIGURATION SPACE REGISTERS
Interface
PCIe
HE
space
XR17V352 R
“Section 1.2, EEPROM Interface” on page
EGISTER
S
ETS
Device Configuration Registers
Device Configuration Registers
registers + enhanced registers
Channel 0 TX FIFO, RX FIFO,
registers + enhanced registers
Channel 1 TX FIFO, RX FIFO,
Channel 0 16550 compatible
Channel 1 16550 compatible
RX FIFO + Status Burst Reg
RX FIFO + Status Burst Reg
Configuration Space
Registers for Plug-
and-Play Auto
PCI Local Bus
Configuration
8
Figure
12) required by the auto-configuration setup.
3. The PCI Local Bus Configuration Space
0x07FF
0x0000
0x0080
0x0100
0x0400
Vendor and Sub-vendor ID
and Product Model Number
in External EEPROM
REV. 1.0.1