MCP4441-502E/ST Microchip Technology, MCP4441-502E/ST Datasheet - Page 57

• Manufacturer Part Number: MCP4441-502E/ST
• Description: IC DGTL POT 129TAPS QUAD 20TSSOP
• Manufacturer: Microchip Technology

Specifications of MCP4441-502E/ST

• Taps: 129
• Resistance (ohms): 5K
• Number Of Circuits: 4
• Temperature Coefficient: 150 ppm/°C Typical
• Memory Type: Non-Volatile
• Interface: I²C, 2-Wire Serial
• Voltage - Supply: 2.7 V ~ 5.5 V
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Surface Mount
• Package / Case: 20-TSSOP (0.173", 4.40mm Width)
• End To End Resistance: 5kohm
• Track Taper: Linear
• Resistance Tolerance: ± 20%
• No. Of Steps: 129
• Supply Voltage Range: 2.7V To 5.5V
• Control Interface: I2C
• No. Of Pots: Quad
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

6.2.6
The I
device must be ‘activated’ to operate in high-speed
(3.4 Mbit/s) mode. This is done by the Master sending
a special address byte following the START bit. This
byte is referred to as the high-speed Master Mode
Code (HSMMC).
The MCP44XX device does not acknowledge this byte.
However, upon receiving this command, the device
switches to HS mode. The device can now
communicate at up to 3.4 Mbit/s on SDA and SCL
lines. The device will switch out of the HS mode on the
next STOP condition.
The master code is sent as follows:
1.
2.
3.
FIGURE 6-10:
© 2010 Microchip Technology Inc.
S
START condition (S)
High-Speed Master Mode Code (0000 1XXX),
The XXX bits are unique to the high-speed (HS)
mode Master.
No Acknowledge (A)
2
R/W = Read/Write bit
C specification requires that a high-speed mode
F/S-mode
‘0 0 0 0 1 X X X’b
Sr = Repeated Start bit
S = Start bit
A = Acknowledge bit
A = Not Acknowledge bit
P = Stop bit (Stop condition terminates HS Mode)
HS Select Byte
HS MODE
HS Mode Sequence.
A
Sr
HS-mode
‘Slave Address’
Control Byte
R/W
A
Command/Data Byte(s)
After switching to the High-Speed mode, the next
transferred byte is the I
the device to communicate with, and any number of
data bytes plus acknowledgements. The Master
Device can then either issue a Repeated Start bit to
address a different device (at High-Speed) or a Stop bit
to return to Fast/Standard bus speed. After the Stop bit,
any other Master Device (in a Multi-Master system) can
arbitrate for the I
See
sequence.
For more information on the HS mode, or other I
modes, please refer to the Phillips I
6.2.6.1
The slope control on the SDA output is different
between the Fast/Standard Speed and the High-Speed
clock modes of the interface.
6.2.6.2
The pulse gobbler on the SCL pin is automatically
adjusted to suppress spikes < 10 ns during HS mode.
“Data”
Figure 6-10
Slope Control
Pulse Gobbler
A/A
MCP444X/446X
2
for illustration of HS mode command
C bus.
Sr
P
‘Slave Address’ R/W
HS-mode continues
2
C control byte, which specifies
Control Byte
F/S-mode
2
DS22265A-page 57
C specification.
A
2
C