ATMEGA165PV-8MNR Atmel, ATMEGA165PV-8MNR Datasheet - Page 105
![IC MCU AVR 16K 8MHZ 64MLF](/photos/12/13/121326/313-64-qfn_sml.jpg)
ATMEGA165PV-8MNR
Manufacturer Part Number
ATMEGA165PV-8MNR
Description
IC MCU AVR 16K 8MHZ 64MLF
Manufacturer
Atmel
Series
AVR® ATmegar
Specifications of ATMEGA165PV-8MNR
Core Processor
AVR
Core Size
8-Bit
Speed
8MHz
Connectivity
SPI, UART/USART, USI
Peripherals
Brown-out Detect/Reset, POR, PWM, WDT
Number Of I /o
54
Program Memory Size
16KB (8K x 16)
Program Memory Type
FLASH
Eeprom Size
512 x 8
Ram Size
1K x 8
Voltage - Supply (vcc/vdd)
1.8 V ~ 5.5 V
Data Converters
A/D 8x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
64-VFQFN, Exposed Pad
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
- Current page: 105 of 364
- Download datasheet (8Mb)
14.6.1
14.6.2
14.6.3
8019K–AVR–11/10
Input Capture Trigger Source
Noise Canceler
Using the Input Capture Unit
The ICR1 Register can only be written when using a Waveform Generation mode that utilizes
the ICR1 Register for defining the counter’s TOP value. In these cases the Waveform Genera-
tion mode (WGM1[3:0]) bits must be set before the TOP value can be written to the ICR1
Register. When writing the ICR1 Register the high byte must be written to the ICR1H I/O location
before the low byte is written to ICR1L.
For more information on how to access the 16-bit registers refer to
on page
The main trigger source for the Input Capture unit is the Input Capture pin (ICP1).
Timer/Counter1 can alternatively use the Analog Comparator output as trigger source for the
Input Capture unit. The Analog Comparator is selected as trigger source by setting the Analog
Comparator Input Capture (ACIC) bit in the Analog Comparator Control and Status Register
(ACSR). Be aware that changing trigger source can trigger a capture. The Input Capture Flag
must therefore be cleared after the change.
Both the Input Capture pin (ICP1) and the Analog Comparator output (ACO) inputs are sampled
using the same technique as for the T1 pin
identical. However, when the noise canceler is enabled, additional logic is inserted before the
edge detector, which increases the delay by four system clock cycles. Note that the input of the
noise canceler and edge detector is always enabled unless the Timer/Counter is set in a Wave-
form Generation mode that uses ICR1 to define TOP.
An Input Capture can be triggered by software by controlling the port of the ICP1 pin.
The noise canceler improves noise immunity by using a simple digital filtering scheme. The
noise canceler input is monitored over four samples, and all four must be equal for changing the
output that in turn is used by the edge detector.
The noise canceler is enabled by setting the Input Capture Noise Canceler (ICNC1) bit in
Timer/Counter Control Register B (TCCR1B). When enabled the noise canceler introduces addi-
tional four system clock cycles of delay from a change applied to the input, to the update of the
ICR1 Register. The noise canceler uses the system clock and is therefore not affected by the
prescaler.
The main challenge when using the Input Capture unit is to assign enough processor capacity
for handling the incoming events. The time between two events is critical. If the processor has
not read the captured value in the ICR1 Register before the next event occurs, the ICR1 will be
overwritten with a new value. In this case the result of the capture will be incorrect.
When using the Input Capture interrupt, the ICR1 Register should be read as early in the inter-
rupt handler routine as possible. Even though the Input Capture interrupt has relatively high
priority, the maximum interrupt response time is dependent on the maximum number of clock
cycles it takes to handle any of the other interrupt requests.
Using the Input Capture unit in any mode of operation when the TOP value (resolution) is
actively changed during operation, is not recommended.
Measurement of an external signal’s duty cycle requires that the trigger edge is changed after
each capture. Changing the edge sensing must be done as early as possible after the ICR1
100.
(Figure 15-1 on page
126). The edge detector is also
“Accessing 16-bit Registers”
ATmega165P
105
Related parts for ATMEGA165PV-8MNR
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![ATmega165P](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
Manufacturer:
Atmel Corporation
Datasheet:
![ATMEGA165P-16AU](/photos/12/13/121332/313-64-tqfp_tmb.jpg)
Part Number:
Description:
IC AVR MCU 16K 16MHZ 64-TQFP
Manufacturer:
Atmel
Datasheet:
![ATMEGA165P-16MU](/photos/12/13/121326/313-64-qfn_tmb.jpg)
Part Number:
Description:
IC AVR MCU 16K 16MHZ 64-QFN
Manufacturer:
Atmel
Datasheet:
![ATMEGA165P-16AUR](/photos/12/13/121332/313-64-tqfp_tmb.jpg)
Part Number:
Description:
MCU AVR 128K FLASH 16MHZ 64TQFP
Manufacturer:
Atmel
Datasheet:
![ATMEGA165P-16MN](/photos/12/13/121326/313-64-qfn_tmb.jpg)
Part Number:
Description:
MCU AVR 16KB FLASH 16MHZ 64QFN
Manufacturer:
Atmel
Datasheet:
![ATMEGA165P-16MUR](/photos/12/13/121326/313-64-qfn_tmb.jpg)
Part Number:
Description:
IC MCU AVR 16K 16MHZ 64MLF
Manufacturer:
Atmel
Datasheet:
![ATMEGA165P-16ANR](/photos/12/13/121332/313-64-tqfp_tmb.jpg)
Part Number:
Description:
IC MCU AVR 16K 16MHZ 64TQFP
Manufacturer:
Atmel
Datasheet:
![ATMEGA165P-16MNR](/photos/12/13/121326/313-64-qfn_tmb.jpg)
Part Number:
Description:
IC MCU AVR 16K 16MHZ 64MLF
Manufacturer:
Atmel
Datasheet:
![ATMEGA165P-16AN](/images/manufacturer_photos/0/0/78/atmel_tmb.jpg)
Part Number:
Description:
8-bit Microcontrollers - MCU AVR 16KB FL 512B EE 1KB SRAM 16 MHZ GRN
Manufacturer:
Atmel
![atmega165pv](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
Atmega165p 8-bit Avr Microcontroller With 16k Bytes In-system Programmable Flash
Manufacturer:
ATMEL Corporation
Datasheet:
![ATMEGA165-16AI](/photos/12/13/121332/313-64-tqfp_tmb.jpg)
Part Number:
Description:
IC AVR MCU 16K 16MHZ 64TQFP
Manufacturer:
Atmel
Datasheet:
![ATMEGA165-16MI](/images/manufacturer_photos/0/0/78/atmel_tmb.jpg)
Part Number:
Description:
IC AVR MCU 16K 16MHZ 64-QFN
Manufacturer:
Atmel
Datasheet:
![ATMEGA165](/images/no-image3.png)
Part Number:
Description:
8-bit Microcontroller with 16K Bytes In-System Programmable Flash
Manufacturer:
ATMEL [ATMEL Corporation]
Datasheet:
![ATMEGA165-16MU](/images/manufacturer_photos/0/0/78/atmel_tmb.jpg)
Part Number:
Description:
IC AVR MCU 16K 16MHZ 64-QFN
Manufacturer:
Atmel
Datasheet: