TFDU6103-TR3 Vishay, TFDU6103-TR3 Datasheet - Page 2

• Manufacturer Part Number: TFDU6103-TR3
• Description: Infrared Transceivers SIR 115.2kbits Side View
• Manufacturer: Vishay
• Type: Fastr

Specifications of TFDU6103-TR3

• Data Transmission Rate: 4000 Kbits/s
• Input Current: 10 mA
• Mounting Style: SMD/SMT
• Power Dissipation: 500 mW
• Wavelength: 886 nm
• Continual Data Transmission: 4 Mbit/s
• Transmission Distance: 1 m
• Radiant Intensity: 170 mW/sr
• Half Intensity Angle Degrees: 48 deg
• Pulse Width: 2.1 us
• Maximum Rise Time: 40 ns
• Maximum Fall Time: 40 ns
• Led Supply Voltage: - 0.5 V to 6.5 V
• Maximum Forward Current: 10 mA
• Operating Voltage: 2.4 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 25 C
• Dimensions: 9.7 mm x 4.7 mm x 4 mm
• Data Rate Max: 4Mbps
• Data Transmission Distance: 1m
• Peak Wavelength: 886nm
• Supply Current: 2mA
• Supply Voltage Range: 2.4V To 5.5V
• Operating Temperature Range: -25°C To +85°C
• Msl: MSL 4 - 72 Hours
• Data Rate: 4Mbps
• Angle Of Half Sensitivity: 48°
• Communication Distance: 100
• Package Type: Ultra Small Profile
• Fall Time: 40ns
• Rise Time: 40ns
• Operating Supply Voltage (typ): 2.5/3.3/5V
• Operating Supply Voltage (min): 2.4V
• Operating Supply Voltage (max): 5.5V
• Mounting: Surface Mount
• Pin Count: 8
• Operating Temp Range: -25C to 85C
• Operating Temperature Classification: Commercial
• Idle Current, Typ @ 25° C: 2mA
• Link Range, Low Power: 1m
• Operating Temperature: -25°C ~ 85°C
• Orientation: Side View
• Shutdown: *
• Size: 9.7mm x 4.7mm x 4mm
• Standards: IrPHY 1.4
• Supply Voltage: 2.4 V ~ 5.5 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

TFDU6103
Vishay Semiconductors
FUNCTIONAL BLOCK DIAGRAM
PINOUT
TFDU6103
weight 0.2 g
www.vishay.com
2
PIN DESCRIPTION
NUMBER
PIN
1
2
3
4
5
6
7
8
17087
IRED anode
SYMBOL
cathode
IRED
GND
V
RXD
V
TXD
SD
NC
CC2
CC1
”U” Option Baby Face (universal)
18468
1
IRED
[e-mail], [e-mail],
Shutdown, also used for dynamic mode switching. Setting this pin active places the module
into shutdown mode. On the falling edge of this signal, the state of the TXD pin is sampled
2
Received data output, push-pull CMOS driver output capable of driving a standard CMOS
Connect IRED anode directly to V
disables the LED driver if the TXD pin is asserted for longer than 100 µs. When used in
This input is used to transmit serial data when SD is low. An on-chip protection circuit
For technical questions within your region, please contact one of the following:
3
SD
TXD
4
conjunction with the SD pin, this pin is also used to set receiver speed mode
and used to set receiver low bandwidth (TXD = low, SIR) or high bandwidth
5
Floating with a weak pull-up of 500 k (typ.) in shutdown mode
or TTL load. No external pull-up or pull-down resistor is required.
6
might be necessary for reducing the internal power dissipation.
An unregulated separate power supply can be used at this pin
Fast Infrared Transceiver Module (FIR, 4 Mbit/s)
Detector
7
IRED cathode, internally connected to driver transistor
8
Am pl if ie r
(TXD = high, MIR and FIR) mode
for 2.4 V to 5.5 V Operation
CC2
DESCRIPTION
Supply voltage
. For voltages higher than 3.6 V an external resistor
Co mp ar ator
Lo gi c
and
Contro l
Ground
GND
Definitions:
In the Vishay transceiver datasheets the following
nomenclature is used for defining the IrDA operating modes:
SIR: 2.4 kbit/s to 115.2 kbit/s, equivalent to the basic serial
infrared standard with the physical layer version IrPhy 1.0
MIR: 576 kbit/s to 1152 kbit/s
FIR: 4 Mbit/s
VFIR: 16 Mbit/s
MIR and FIR were implemented with IrPhy 1.1, followed by
IrPhy 1.2, adding the SIR low power standard. IrPhy 1.3
extended the low power option to MIR and FIR and VFIR was
added with IrPhy 1.4. A new version of the standard in any
case obsoletes the former version.
Note
We apologize to use sometimes in our documentation the
abbreviation LED and the word light emitting diode instead of
infrared emitting diode (IRED) for IR-emitters. That is by definition
wrong; we are here following just a bad trend.
Typical values are for design aid only, not guaranteed nor subject to
production testing and may vary with time.
V
CC1
[e-mail]
Contro lle d
Dr iv er
Tr i- Stat e
Dr iv er
IR ED C
V
RXD
CC2
Document Number: 81211
Rev. 1.4, 29-Jul-09
I/O
O
I
I
ACTIVE
High
High
Low