UM232R FTDI, UM232R Datasheet - Page 11

• Manufacturer Part Number: UM232R
• Description: Interface Modules & Development Tools USB to Serial UART Dev Mod for FT232R
• Manufacturer: FTDI
• Type: Development Moduler

Specifications of UM232R

• Interface Type: USB, Serial, UART
• Data Bus Width: Serial
• Operating Supply Voltage: 1.8 V to 5.25 V
• Product: Interface Modules
• Supported Devices: FT232R
• Svhc: No SVHC (18-Jun-2010)
• Development Tool Type: Development Kit
• Kit Features: Single Chip USB To Asynchronous Serial Data Transfer Interface, Auto Transmit Buffer
• Rohs Compliant: Yes
• Supported Families: FT232RL
• Features: Single Chip USB To Asynchronous Serial Data Transfer Interface, Auto Transmit Buffer Control
• Tool / Board Applications: USB To
• For Use With/related Products: FT232R
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

4.4 CBUS Signal Options
The following options can be configured on the CBUS I/O pins. These options are all configured in the
internal EEPROM using the utility software FT_PROG, which can be downloaded from the www.ftdichip.com.
The default configuration is described in
CBUS Signal
Option
TXDEN#
PWREN#
TXLED#
RXLED#
TX&RXLED#
SLEEP#
CLK48
CLK24
CLK12
CLK6
CBitBangI/O
BitBangWRn
BitBangRDn
Table 4.4 CBUS Signal Options
© Copyright 2009 Future Technology Devices International Ltd
Available On CBUS Pin
CBUS0, CBUS1, CBUS2, CBUS3,
CBUS4
CBUS0, CBUS1, CBUS2, CBUS3,
CBUS4
CBUS0, CBUS1, CBUS2, CBUS3,
CBUS4
CBUS0, CBUS1, CBUS2, CBUS3,
CBUS4
CBUS0, CBUS1, CBUS2, CBUS3,
CBUS4
CBUS0, CBUS1, CBUS2, CBUS3,
CBUS4
CBUS0, CBUS1, CBUS2, CBUS3,
CBUS4
CBUS0, CBUS1, CBUS2, CBUS3,
CBUS4
CBUS0, CBUS1, CBUS2, CBUS3,
CBUS4
CBUS0, CBUS1, CBUS2, CBUS3,
CBUS4
CBUS0, CBUS1, CBUS2, CBUS3
CBUS0, CBUS1, CBUS2, CBUS3
CBUS0, CBUS1, CBUS2, CBUS3
UM232R USB - Serial UART Development Module Incorporating Clock Generator
Section
9.
Description
Enable transmit data for RS485
Goes low after the device is configured by USB, then high
during USB suspend. Can be used to control power to
external logic in high power designs. Needs 10k pull up to
VCC.
Transmit data LED drive – pulses low when transmitting
data via USB.
Receive data LED drive – pulses low when receiving data
via USB.
LED drive – pulses low when transmitting or receiving
data via USB. See
Goes low during USB suspend mode. Typically used to
power down an external TTL to RS232 level converter I.C.
in USB to RS232 converter designs.
48MHz Clock output.
24 MHz Clock output.
12 MHz Clock output.
6 MHz Clock output.
CBUS bit bang mode option. Allows up to 4 of the CBUS
pins to be used as general purpose I/O. Configured
individually for CBUS0, CBUS1, CBUS2 and CBUS3 in the
internal EEPROM. A separate application note will describe
in more detail how to use CBUS bit bang mode.
(www.ftdichip.com)
Synchronous and asynchronous bit bang mode WR#
strobe Output.
Synchronous and asynchronous bit bang mode RD#
strobe Output.
Document Reference No.: FT_000051
Clearance No.: FTDI# 125
Datasheet Version 1.04
10