AP601-PCB900 TriQuint, AP601-PCB900 Datasheet
![RF Modules & Development Tools 869-960MHz Eval Brd 16dB Gain](/photos/15/97/159769/ap601_sml.jpg)
AP601-PCB900
Specifications of AP601-PCB900
Related parts for AP601-PCB900
AP601-PCB900 Summary of contents
Page 1
... Rating -55 to +125 ºC Ordering Information 192 ºC Part No. Input P6dB 0.1 mA AP601 0.1 mA AP601-PCB900 80 mA AP601-PCB1960 1930-1990 MHz Evaluation board 2.3 W AP601-PCB2140 2110-2170 MHz Evaluation board Functional Diagram SMT The device ACLR1 vs. Output Power vs. Icq WCDMA, Vcc = 28V, 2140 MHz, 25 ˚C ...
Page 2
... AP601 High Dynamic Range 1.8W 28V HBT Amplifier S-Parameters ( Gain / Maximum Stable Gain 40 DB(|S(2,1)|) -10 0 0.5 1 1.5 Frequency (GHz) The gain for the unmatched device in 50 ohm system is shown as the trace in black color. For a tuned circuit for a particular frequency expected that actual gain will be higher the maximum stable gain. The maximum stable gain is shown in the marked red line. ...
Page 3
... Vpd is used as a reference for the internal active bias circuitry. It can be used to turn on/off the amplifier. Ipd depends on the Icq quiescent current setting. Ipd can 2mA at a quiescent current setting of 40mA. 3. Vbias should be maintained fixed at +5V. Ibias will change based on RF input power level. It can 2mA on the AP601 ...
Page 4
... AP601 High Dynamic Range 1.8W 28V HBT Amplifier 869-960 Application Circuit (AP601-PCB900) Typical WCDMA Performance at 25 ° channel power of +24 dBm Frequency (MHz) 880 940 W-CDMA Ch. Power +24 +24 Power Gain 16.5 15.8 Input Return Loss 8.9 14 Output Return Loss 15 7.5 ACLR ...
Page 5
... The center placed at 0.085” (7.3° @ 1960 MHz) from the edge of the AP601 (U1). 5. The center of C19 is placed at 0.755” (64.5° @ 1960 MHz) from the edge of the AP601 (U1). 6. The center of C18 is placed at 0.300” (25.6° @ 1960 MHz) from the center of C19. ...
Page 6
... The center placed at 0.100” (9.3° @ 2140 MHz) from the edge of the AP601 (U1). 6. The center of C19 is placed at 0.760” (70.9° @ 2140 MHz) from the edge of the AP601 (U1). 7. The bold-faced RF trace is for the DC bias feed. The stub’s length is approximately a ¼ λ. ...
Page 7
... AP601 High Dynamic Range 1.8W 28V HBT Amplifier 2110-2170 MHz Application Circuit Performance Plots W-CDMA 3GPP Test Model 1+64 DPCH, 60% clipping, PAR = 8 0.01% Probability, 3.84 MHz BW Gain vs. Output Power vs. Temperature CW tone, Vcc = 28V, Icq = 40 mA, 2140 MHz -40 ˚ ˚C 85 ˚ Output Power (dBm) ACLR1 vs ...
Page 8
... High Dynamic Range 1.8W 28V HBT Amplifier 2110-2170 MHz Application Note: Changing Icq Biasing Configurations The AP601 can be configured to operate with lower bias current by varying the bias-adjust resistor – R2. The recommended circuit configurations shown previously in this datasheet have the device operating with the quiescent current (I This biasing level represents the best tradeoff in terms of linearity and efficiency ...
Page 9
... The center placed at 0.050” (5.1° @ 2.35 GHz) from the edge of the AP601 (U1). 4. The center of C19 is placed at 0.650” (66.6° @ 2.35 GHz) from the edge of the AP601 (U1). 5. The center of C30 is placed at 0.110” (11.3° @ 2.35 GHz) from the center of C19. ...
Page 10
... Junction Temperature (°C) Product Marking The component will be laser marked with a “AP601-F” product label with an alphanumeric lot code on the top surface of the package. Tape and reel specifications for this part will be located on the website in the “Application Notes” section. ...