ISL59605IRZ Intersil, ISL59605IRZ Datasheet - Page 25
![IC VIDEO EQUALIZER 20-QFN](/photos/18/29/182903/20-vqfn_l20c_sml.jpg)
ISL59605IRZ
Manufacturer Part Number
ISL59605IRZ
Description
IC VIDEO EQUALIZER 20-QFN
Manufacturer
Intersil
Series
MegaQ™r
Type
Video Equalizerr
Datasheet
1.ISL59601IRZ-T7.pdf
(27 pages)
Specifications of ISL59605IRZ
Applications
Security Systems, Video Routing
Mounting Type
Surface Mount
Package / Case
20-VFQFN Exposed Pad
Rohs Compliant
Yes
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ISL59605IRZ
Manufacturer:
Intersil
Quantity:
270
Part Number:
ISL59605IRZ
Manufacturer:
INTERSIL
Quantity:
20 000
Company:
Part Number:
ISL59605IRZ-T7
Manufacturer:
Intersil
Quantity:
1 700
Part Number:
ISL59605IRZ-T7
Manufacturer:
INTERSIL
Quantity:
20 000
Register Listing
Bypassing and Layout
Considerations
MegaQ™ requires a dedicated ground plane in
order to function properly. For 2-layer boards, pour a
quarter-inch ground plane extending around the device
on both the top and bottom layers. Ensure that the
ground plane on the bottom layer is a solid plane with
no traces cutting through it. Bypass capacitors must be
placed as close as possible to the device in order to
ensure good performance at longer lengths of
equalization. Ensure that the ground connections for the
bypass capacitors connect directly to the same uniform
ground plane described above.
General PowerPAD Design Considerations
The thermal pad must be connected to the ground plane
for heat dissipation. Figure 50 is an example of how to
use vias to remove heat from the IC.
The thermal pad is electrically connected to GND through
the high resistance IC substrate. We recommend you fill
the thermal pad area with vias. The via array should be
centered in the thermal pad and placed such that the
center on center spacing is 3x the via radius. Vias should
be small, but large enough to allow solder wicking during
reflow. Connect all vias to ground. It is important the vias
have a low thermal resistance for efficient heat transfer.
Do not use “thermal relief” patterns. It is important to
ADDRESS
0x05
Equalization Control
(0x00)
FIGURE 50. PCB VIA PATTERN
(DEFAULT VALUE)
ISL59601, ISL59602, ISL59603, ISL59604, ISL59605
REGISTER
25
(Continued)
BIT(S)
1:0
3:2
4
Locking Mode/Manual
Length Enable
Noise Filter
Coax Mode
FUNCTION NAME
have a solid connection of the plated-through hole to
each plane.
Power Dissipation
The maximum power dissipation allowed in a package is
determined according to Equation 1:
PD
Where:
The maximum power dissipation actually produced by an
IC is the total quiescent supply current times the total
power supply voltage, plus the power in the IC due to the
load, or:
for sourcing use Equation 2:
PD
for sinking use Equation 3:
PD
Where:
T
T
Θ
V
I
V
R
I
MAX
MAX
MAX
SMAX
LOAD
JMAX
AMAX
JA
S
OUT
LOAD
= Supply voltage
= Thermal resistance of the package
=
=
=
= Maximum output voltage of the application
00 = Continuous Monitoring
01 = Lock Until Signal Loss*
10 = Lock Until Reset
11 = Manual Length**
*Signal must be missing for at least 1ms in order to
trigger a re-equalization.
** In Manual Length mode the polarity corrector is
disabled and the polarity must be set using the
INVERT bit or pin.
Note: The FREEZE pin must be tied to ground/a logic
low for this function to work correctly.
00: No Noise Filtering
01: Min Noise Filtering
10 or 11: Max Noise Filtering
Note: Noise Filtering is only available on the ISL59605
0: CAT5/6 Mode
1: Steel Core Coax Mode
This bit is ignored in all modes except Manual
Length (reg 0x05[1:0] = 11).
Set to 1 if using copper-coated steel-core coaxial
cable and you are in Manual Length.
= Load current
= Maximum junction temperature
= Maximum quiescent supply current
T
-------------------------------------------- -
= Maximum ambient temperature
V
V
= Load resistance tied to ground
JMAX
S
S
×
×
I
I
SMAX
SMAX
Θ
–
JA
T
AMAX
+
+
(
(
V
V
S
OUT
–
DESCRIPTION
V
–
OUT
V
S
)
)
×
×
I
V
--------------- -
LOAD
OUT
R
L
November 23, 2010
FN6739.1
(EQ. 1)
(EQ. 2)
(EQ. 3)