2154208-1 TE Connectivity, 2154208-1 Datasheet
2154208-1
Manufacturer Part Number
2154208-1
Description
SSL DRIVR UNIT 2100MA 18.36V 75W
Manufacturer
TE Connectivity
Specifications of 2154208-1
Output Current
2.1A
Output Voltage
36V
Output Power
75W
Input Voltage
90V AC To 305V AC
Power Supply Mounting
Wall
Length
192mm
Width
60mm
Depth
37mm
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
A101441
1. INTRODUCTION
This instruction sheet provides assembly procedures
for the NEVALO LED Driver. This driver is designed to
be a part of a complete LED lighting interconnect
solution. The NEVALO LED Driver mates to the Feed-
Thru, Straight, and Right-Angle connectors. These
connectors are insulation displacement contacts (IDC)
and are terminated to ribbon cable. A terminator
connector is placed on the free end to create a series
circuit between all connectors and the driver.
Read these instructions carefully before assembling
the NEVALO LED Drivers with any connectors.
2. DESCRIPTION
NEVALO LED Drivers operate at a temperature range
of -20° to 60°C [-4° to 140°F] with an operating
humidity of 5% to 85% (non-condensing).
©2011 Tyco Electronics Corporation, Berwyn, PA
All Rights Reserved
TE logo and Tyco Electronics are trademarks.
*Trademark. Other products, logos, and company names might be trademarks of their respective owners.
NOTE
NOTE
COLOR
Orange
Green
Flying Leads
i
i
Blue
Red
NEVALO LED DRIVER
Dimensions on this sheet are in millimeters [with
inch equivalents provided in brackets]. Figures and
illustrations are for identification only and are not
drawn to scale.
It is recommended the maximum temperature be
verified at the thermocouple probe point on the
case (marked “Tc
label.
DRIVE CURRENT
-
1000mA
2100mA
350mA
700mA
”) in the lower right corner of the
TOOLING ASSISTANCE CENTER 1-800-722-1111
PRODUCT INFORMATION 1-800-522-6752
DIMMABLE
NEVALO* LED Driver
Yes
Yes
Yes
No
Figure 1
These drivers are available in four drive currents and
are coded with four colors. All have a molded keying
feature that corresponds to keying features on the
mating interconnects to prevent over/under powering
of light modules. See Figure 1.
All NEVALO LED Drivers should be used with
corresponding colored ribbon cable, light modules,
and interconnects. Refer to Application Specifications
114-13290, 114-13293, and 114-13297. Figure 2
shows connector orientations and color code
locations.
3. DRIVER FEATURES
NEVALO LED Drivers are supplied with 18 AWG
stranded Flying Leads.
LED Driver
CAUTION
Color Code
NOTE
i
!
Black wire connects to line voltage.
White wire connects to neutral.
Green wire connects to ground (if equipped).
Connect input leads to proper AC Input voltage as
specified on the driver label.
This controlled document is subject to change.
For latest revision and Regional Customer Service,
visit our website at www.tycoelectronics.com
Connector Key
408-10419
Instruction Sheet
07 MAR 11 Rev B
1 of 2
LOC B
Related parts for 2154208-1
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Printers THERMAL PRINTER HS-SLEEVE MARKER
Manufacturer:
TE Connectivity
Part Number:
Description:
Manufacturer:
TE Connectivity
Datasheet:
Part Number:
Description:
Manufacturer:
TE Connectivity
Datasheet:
Part Number:
Description:
Manufacturer:
TE Connectivity
Datasheet:
2154208-1 Summary of contents
Page 1
NEVALO LED DRIVER - Flying Leads COLOR DRIVE CURRENT Orange 350mA Red 700mA Green 1000mA Blue 2100mA 1. INTRODUCTION This instruction sheet provides assembly procedures for the NEVALO LED Driver. This driver is designed part of a ...
Page 2
The driver has over-voltage protection. The driver will latch-off under over-voltage conditions. Connect to LED load before turning on. Power up without LED load will result in an over-voltage condition. If LED load is not connected before powering on, connect ...