CBC-EVAL-10 Cymbet Corporation, CBC-EVAL-10 Datasheet - Page 5

• Manufacturer Part Number: CBC-EVAL-10
• Description: ENERCHIP CC SEH EVAL KIT
• Manufacturer: Cymbet Corporation
• Series: EnerChip™ CCr
• Type: Energy Harvestingr

Specifications of CBC-EVAL-10

• Main Purpose: Power Management, Renewable Energy
• Embedded: No
• Utilized Ic / Part: CBC3150, CBC51100
• Primary Attributes: Thin Film Rechargeable Solid State Battery
• Secondary Attributes: Solar Energy Harvester
• Maximum Operating Temperature: + 70 C
• Product: Power Management Development Tools
• For Use With/related Products: EnerChip CBC51100
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: 859-1012

CBC-EVAL-10 Module Connector Descriptions
J3:
See specifications elsewhere in this document for the minimum and maximum allowable battery voltage before
attaching a battery to this connector.
J7:
external 4.1V rechargeable battery. No other connections are allowed on these pins and the pins are not to
be shorted together. See specifications elsewhere in this document for the minimum and maximum allowable
external battery voltage before attaching a battery to this connector.
J8:
document for the minimum and maximum allowable DC voltage to be applied to this connector.
J9 and J10:
(For reference, header connector J9 is a 5-pin section of Samtec 50-pin header p/n TSW-150-07-G-S. Header
connector J10 is Mill-Max p/n 850-10-006-20-001000; the socket it mates to is Mill-Max p/n 851-93-006-20-
001000.)
J14:
Cable Assembly
facilitate connection between the J9 connector and a 5-pin header on the user’s board.
Getting Started
To operate the CBC-EVAL-10 in the standard energy harvesting mode, using the EnerChips as the storage
devices, leave each of the several jumpers in the same position as received. The factory default settings are as
follows:
DS-72-20 Rev A
Header pins to be used only for the purpose of connecting the positive and negative terminals of an
Terminal block for connecting the positive and negative terminals of an external non-rechargeable battery.
Terminal block for connecting a photovoltaic cell (or other DC voltage). See specifications elsewhere in this
Used for factory test purposes only. Do not make any connections to J14.
Header
J1
J2
J3
J4
J5
J6
J7
J8
J9
J10
J11
J12
J13
J14
J15
Power and handshaking signals for connection to a target board - e.g. wireless end-point module.
- A 5-conductor cable with a header connector at each end is provided with CBC-EVAL-10 to
©2011 Cymbet Corporation • Tel: [phone] • www.cymbet.com
Shorting Jumper, Connector, or Solder Trace/Pad
No
No
No
Yes
Yes
Yes
No. DO NOT APPLY A SHORTING JUMPER TO J7 UNDER ANY CIRCUMSTANCES! Doing
so will destroy the EnerChips.
PV Cell Input (2.5VDC to 5.5VDC)
System I/O (See J9 and J10 Pin Descriptions Table)
System I/O (See J9 and J10 Pin Descriptions Table)
Pin 3 to Pin 4
Leave as is for 2.5V Regulated Output (Cut J12 and Short J13 for 3.0V Regulation)
Leave as is for 2.5V Regulated Output (Cut J12 and Short J13 for 3.0V Regulation)
No Connections Necessary (Used for Factory Testing)
Leave as is for 2.5V Regulated Output
CBC-EVAL-10 EnerChip CC EH Evaluation Kit
Page 5 of 15