AS5013-DB-2.1 austriamicrosystems, AS5013-DB-2.1 Datasheet

Page 1

... AS5013-DB-2.1 Lower Power Integrated Hall IC for Human Interface Applications 1 General Description The AS5013 is a complete Hall Sensor IC for smart navigation key applications to meet the low power requirements and host SW integration challenges for products such as cell phones and smart handheld devices. Due to the on chip processing engine, system designers are not tasked with integrating complex SW algorithms on their host processor thus leading to rapid development cycles. The AS5013 single-chip IC includes 5 integrated Hall sensing elements for detecting up to ± ...

Page 2

... AS5013-DB-2.1 Demoboard and Software Operation Manual Center LED USB plug (to PC) Button EP Left EasyPoint™ N40P112 module EasyPoint™ N40P112 module: Moving the knob of the EasyPoint module acts like an analog joystick, sending progressive XY coordinates to Windows via USB. Button EP (EasyPoint™ module push): The EasyPoint™ ...

Page 3

... Windows detects an AS5011 HID Joystick control. This part is used for direct communication between the PC and the AS5013 IC. It needs a driver which will be installed by the AS501x Evaluation software installer. Please see chapter 4 for more information. The AS5013 Demoboard can be configured in different ways without any software. ...

Page 4

... AS5013-DB-2.1 Demoboard and Software Operation Manual HID Joystick button I is controlled by the EP button (from the EasyPoint™ module) and Button Mode 1: Push and hold Button The LED “Center” blinks 4 times Joystick button I is controlled by the Button Mode 2: Push and hold Button The LED “ ...

Page 5

... AS5013-DB-2.1 Demoboard and Software Operation Manual 4 First Time Installation As the AS5013 Demoboard works like a standard HID mouse, no software is needed to test it. But for more flexibility and in order to become familiar with the principle of the AS5013 sensor, the AS5013 Mouse GUI software allows to modify the device registers, read the magnet coordinates and change some attribute of the mouse. ...

Page 6

... AS5013-DB-2.1 Demoboard and Software Operation Manual Now Follow the instructions: Center the joystick (release it) and click Next. Center the joystick again (release it) and click Next. Pushing the EP Button and Button Pushing Button on the board activates the button 2 indicator. Pushing Button on the board activates the button 3 indicator. ...

Page 7

... AS5013-DB-2.1 Demoboard and Software Operation Manual 5 AS5013 Evaluation Software Once the AS5013-DB demoboard has been correctly calibrated, the evaluation can start. The software has three tabs: • Mouse Control • Advanced • Plugins 5.1 Mouse Control Tab The AS5013 Evaluation Software includes a mouse emulator, enabled by default. Moving the knob on the demoboard will control the mouse with progressive speed: small knob movements will move the mouse slowly, large mouse movements will move the mouse with a high speed velocity ...

Page 8

... AS5013-DB-2.1 Demoboard and Software Operation Manual 5.2 Advanced Tab This tab gives access to advanced controls: • Hall Push button threshold control • Mouse emulator control • I²C register access to AS5013 registers • Firmware controls of the demoboards MCU Figure 4. Advanced Tab Hall Push Button: Changes the threshold value for the hall push button detection. A typical value is 40. “ ...

Page 9

... AS5013-DB-2.1 Demoboard and Software Operation Manual • Load Custom Settings : Load any mouse setting (.ini file), and sets automatically the Speed, Center Range and Pointer Trails with those saved settings. • Load Default Settings: Different mouse settings can be assigned independently to each plugin (see next chapter “ ...

Page 10

... AS5013-DB-2.1 Demoboard and Software Operation Manual The offset values are computed when the demoboard is powered up, to compensate an eventual mechanical misalignment of the knob at the zero position. The calculation of X Joy (the same is applied for Y Joy): • Center Ampl.: Controls the dead zone area width around the zero position. Used only for the LED control on the demoboard ...

Page 11

... AS5013-DB-2.1 Demoboard and Software Operation Manual Progressive Volume control: Moving the EasyPoint™ button down, the volume will increase or decrease. The speed of the volume button is progressive with the EasyPoint™ knob's vertical position. 5.2.2 Multiple Functions on one Stick • Blobby Volley Simple volley game using left and right movement for moving the green blob, push button to jump. • ...

Page 12

... AS5013-DB-2.1 Demoboard and Software Operation Manual 6 AS5013 Demoboard Hardware 6.1 Schematics Figure 8. AS5013_DB_2.1 Schematics U1 Vusb 7 RegIn C1 10u 3.3V 6 VDD GND GND GND RST/C2CK ISP 10 2 3.3V P3.0/C2D 3 4 Header 4 GND J3 Vusb 8 1 VBUS USB USB_mini GND C8051F320 R19 4.7k SCK U4 3.3V ...

Page 13

... AS5013-DB-2.1 Demoboard and Software Operation Manual 6.2 Layout Figure 9. PCB Top View www.austriamicrosystems.com Revision 1.01 13 – 16 ...

Page 14

... AS5013-DB-2.1 Demoboard and Software Operation Manual Figure 10. PCB Bottom View www.austriamicrosystems.com Revision 1.01 14 – 16 ...

Page 15

... AS5013-DB-2.1 Demoboard and Software Operation Manual 7 Internet Website References austriamicrosystems EasyPoint™ website, general information about AS5013 and EasyPoint™ modules: http://www.austriamicrosystems.com/eng/Products/Magnetic-Encoders/EasyPoint-Joystick-Encoder AS5013-DB demoboard information and software: http://www.austriamicrosystems.com/eng/Support/Design-Resources/Demo-Eval.-Progr.-Boards/EasyPoint-Linear- Encoder/EasyPoint-AS5013-DB-Demoboard Wintech Technology, EasyPoint™ modules manufacturer: http://www.wintectechnology.com/ ...

Page 16

... AS5013-DB-2.1 Demoboard and Software Operation Manual Copyrights Copyright © 1997-2011, austriamicrosystems AG, Schloss Premstaetten, 8141 Unterpremstaetten, Austria-Europe. Trademarks Registered ®. All rights reserved. The material herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. ...