S25FL128P0XMFI001 Spansion Inc., S25FL128P0XMFI001 Datasheet - Page 40

• Manufacturer Part Number: S25FL128P0XMFI001
• Description: IC, FLASH, 128MBIT, 104MHZ, SOIC-16
• Manufacturer: Spansion Inc.

Specifications of S25FL128P0XMFI001

• Memory Type: Flash
• Memory Size: 128Mbit
• Ic Interface Type: Serial, SPI
• Clock Frequency: 104MHz
• Supply Voltage Range: 2.7 To 3.6 V
• Memory Case Style: SOIC
• No. Of Pins: 16
• Data Bus Width: 1 bit
• Architecture: Uniform
• Interface Type: SPI Serial
• Supply Voltage (max): 3.6 V
• Supply Voltage (min): 2.7 V
• Maximum Operating Current: 26 mA
• Mounting Style: SMD/SMT
• Operating Temperature: + 85 C
• Package / Case: SO-16
• Cell Type: NOR
• Density: 128Mb
• Boot Type: Not Required
• Address Bus: 1b
• Operating Supply Voltage (typ): 3/3.3V
• Package Type: SOIC W
• Program/erase Volt (typ): 2.7 to 3.6V
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Operating Supply Voltage (min): 2.7V
• Operating Supply Voltage (max): 3.6V
• Word Size: 1b
• Number Of Words: 128Mword
• Supply Current: 22mA
• Mounting: Surface Mount
• Pin Count: 16
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

14. Initial Delivery State
15. Absolute Maximum Ratings
40
The device is delivered with all bits set to 1 (each byte contains FFh) upon initial factory shipment. The Status
Register contains 00h (all Status Register bits are 0).
Do not stress the device beyond the ratings listed in this section, or serious, permanent damage to the device
may result. These are stress ratings only and device operation at these or any other conditions beyond those
indicated in this section and in the
operation for extended periods at the limits listed in this section may affect device reliability.
Notes
1. Minimum DC voltage on input or I/O pins is –0.5 V. During voltage transitions, input at I/O pins may overshoot V
2. No more than one output may be shorted to ground at a time. Duration of the short circuit should not be greater than one second.
3. Stresses above those listed under
Ambient Storage Temperature
Voltage with Respect to Ground: All Inputs and I/Os
up to 20 ns. See
to V
functional operation of the device at these or any other conditions above those indicated in the operational sections of this data sheet is not
implied. Exposure of the device to absolute maximum rating conditions for extended periods may affect device reliability.
V
CC
V
Symbol
V
CC
CC
CC(min)
(cut-off)
t
t
PU
PD
+ 2.0V for periods up to 20 ns. See
(low)
Figure
V
V
V
V
V
V
CC
CC
CC
CC
CC
CC
15.2. Maximum DC voltage on output and I/O pins is 3.6 V. During voltage transitions output pins may overshoot
(minimum operation voltage)
(Cut off where re-initialization is needed)
(Low voltage for initialization to occur at read/standby)
(Low voltage for initialization to occur at embedded)
(min) to device operation
(low duration time)
Description
Table 13.1 Power-Up / Power-Down Voltage and Timing
Figure 15.1 Maximum Negative Overshoot Waveform
+0.8 V
–0.5 V
–2 V
Absolute Maximum Ratings
Operating Ranges
Table 15.1 Absolute Maximum Ratings
Figure
S25FL128P
15.2.
Parameter
D a t a
20 ns
may cause permanent damage to the device. This is a stress rating only;
section of this document is not implied. Device
S h e e t
20 ns
20 ns
S25FL128P_00_08 September 8, 2009
–0.5V to V
–65°C to +150°C
Rating
Min
300
2.7
2.4
0.2
2.3
1.0
CC
+0.5V
SS
Max
to –2.0V for periods of
Unit
µs
µs
V
V
V