LTC3675EUFF#PBF Linear Technology, LTC3675EUFF#PBF Datasheet - Page 22
![IC, PMIC, 1A, QFN-44](/photos/19/3/190363/4243289_sml.jpg)
LTC3675EUFF#PBF
Manufacturer Part Number
LTC3675EUFF#PBF
Description
IC, PMIC, 1A, QFN-44
Manufacturer
Linear Technology
Datasheet
1.LTC3675EUFFPBF.pdf
(36 pages)
Specifications of LTC3675EUFF#PBF
Supply Voltage
5.5V
No. Of Step-down Dc - Dc Converters
4
No. Of Ldo Regulators
1
Digital Ic Case Style
QFN
No. Of Pins
44
No. Of Regulated Outputs
7
Operating Temperature Range
-40°C To +125°C
Rohs Compliant
Yes
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
OPERATION
LTC3675
I
A bus master signals the beginning of communications
by transmitting a START condition. A START condition is
generated by transitioning SDA from HIGH to LOW while
SCL is HIGH. The master may transmit either the slave
write or the slave read address. Once data is written to the
LTC3675, the master may transmit a STOP condition which
commands the LTC3675 to act upon its new command set.
A STOP condition is sent by the master by transitioning
SDA from LOW to HIGH while SCL is HIGH. The bus is
then free for communication with another I
I
Each byte sent to or received from the LTC3675 must
be 8 bits long followed by an extra clock cycle for the
acknowledge bit. The data should be sent to the LTC3675
most signifi cant bit (MSB) fi rst.
I
The acknowledge signal is used for handshaking between
the master and the slave. When the LTC3675 is written
to (write address), it acknowledges its write address as
well as the subsequent two data bytes. When it is read
from (read address), the LTC3675 acknowledges its read
address only. The bus master should acknowledge receipt
of information from the LTC3675.
An acknowledge (active LOW) generated by the LTC3675
lets the master know that the latest byte of information was
received. The acknowledge related clock pulse is generated
by the master. The master releases the SDA line (HIGH)
during the acknowledge clock cycle. The LTC3675 pulls
down the SDA line during the write acknowledge clock
pulse so that it is a stable LOW during the HIGH period
of this clock pulse.
When the LTC3675 is read from, it releases the SDA line
so that the master may acknowledge receipt of the data.
Since the LTC3675 only transmits one byte of data during
a read cycle, a master not acknowledging the data sent
by the LTC3675 has no I
operation of the I
22
2
2
2
C Start and Stop Conditions
C Byte Format
C Acknowledge
2
C port.
2
C specifi c consequence on the
2
C device.
I
The LTC3675 responds to a 7-bit address which has been
factory programmed to b’0001001[R/WB]’. The LSB of
the address byte, known as the read/write bit, should be 0
when writing data to the LTC3675 and 1 when reading data
from it. Considering the address as an 8-bit word, the write
address is 12h and the read address is 13h. The LTC3675
will acknowledge both its read and write address.
I
The LTC3675 has twelve command registers for control
input. They are accessed by the I
dressed writing system.
A single write cycle of the LTC3675 consists of exactly three
bytes except when a clear interrupt command is written.
The fi rst byte is always the LTC3675’s write address. The
second byte represents the LTC3675’s sub-address. The
sub-address is a pointer which directs the subsequent
data byte within the LTC3675. The third byte consists of
the data to be written to the location pointed to by the
sub-address. The LTC3675 contains 11 control registers
which can be written to.
I
The master initiates communication with the LTC3675
with a START condition and the LTC3675’s write address.
If the address matches that of the LTC3675, the LTC3675
returns an acknowledge. The master should then deliver
the sub-address. Again the LTC3675 acknowledges and
the cycle is repeated for the data byte. The data byte is
transferred to an internal holding latch upon the return of
its acknowledge by the LTC3675. This procedure must be
repeated for each sub-address that requires new data. After
one or more cycles of [ADDRESS][SUB-ADDRESS][DATA],
the master may terminate the communication with a STOP
condition. Multiple sub addresses may be written to with
a single address command using a [ADDRESS][SUB-
ADDRESS][DATA][SUB-ADDRESS][DATA] sequence.
Alternatively, a REPEAT-START condition can be initiated
by the master and another chip on the I
addressed. This cycle can continue indefi nitely and the
LTC3675 will remember the last input of valid data that it
2
2
2
C Slave Address
C Sub-Addressed Writing
C Bus Write Operation
2
C port via a sub-ad-
2
C bus can be
3675f