HT6014-18DIPLF HOLTEK, HT6014-18DIPLF Datasheet
HT6014-18DIPLF
Specifications of HT6014-18DIPLF
Related parts for HT6014-18DIPLF
HT6014-18DIPLF Summary of contents
Page 1
... Other remote control systems grammable address/data which meet various appli- cations. The programmable address/data is transmitted together with the header bits via infrared transmission medium upon receipt of a trigger signal (HT6010 DATA (HT6012/HT6014) trigger can be selected for application flexibility. Data LED Oscillator Trigger No ...
Page 2
... Block Diagram TE Trigger HT6010 DATA Trigger HT6012/HT6014 Note: The address/data pins are available in various combinations (refer to the address/data table). Rev. 1.20 HT6010/HT6012/HT6014 2 September 9, 2003 ...
Page 3
... Pin Assignment Rev. 1.20 HT6010/HT6012/HT6014 3 September 9, 2003 ...
Page 4
... OSCILLATOR Oscillator output pin VSS Negative power supply, ground VDD Positive power supply Note: D8~D11 are data input and transmission enable pins of the HT6012/HT6014 the transmission enable pin of the HT6010. Approximate Internal Connections Absolute Maximum Ratings Supply Voltage ............................V 0. Input Voltage ................................V ...
Page 5
... HT6010 or D8~D11 for the HT6012/HT6014, active low). This cycle will repeat itself as long as the transmission enable (TE or D8~D11) is held low. Once the transmission enable returns high the encoder output completes its final cycle and then stops as shown below ...
Page 6
... A0 to AD11 for the HT6010 and A0 to D11 for the HT6012/HT6014. If the trigger signal is not applied, the chip only consumes a standby current which is less than 1 A (for V The address pins are usually preset transmit data codes with their own particular security codes by the DIP switches or PCB wiring, while data is selected using push button or electronic switches ...
Page 7
... Flowchart Note: D8~D11 are transmission enable of the HT6012/HT6014 the transmission enable of the HT6010. Oscillator Frequency vs. Supply Voltage The recommended oscillator frequency is f Rev. 1.20 HT6010/HT6012/HT6014 (decoder (encoder) OSCD OSCE 7 September 9, 2003 ...
Page 8
... Application Circuits Rev. 1.20 HT6010/HT6012/HT6014 8 September 9, 2003 ...
Page 9
... Package Information 18-pin DIP (300mil) Outline Dimensions Symbol Min. A 895 B 240 C 125 D 125 295 I 335 0 Rev. 1.20 HT6010/HT6012/HT6014 Dimensions in mil Nom. Max. 915 260 135 145 20 70 100 315 375 15 9 September 9, 2003 ...
Page 10
... SOP (300mil) Outline Dimensions Symbol Min. A 394 B 290 C 14 490 Rev. 1.20 HT6010/HT6012/HT6014 Dimensions in mil Nom. Max. 419 300 20 510 104 September 9, 2003 ...
Page 11
... Reel Dimensions SOP 20W Symbol Description A Reel Outer Diameter B Reel Inner Diameter C Spindle Hole Diameter D Key Slit Width T1 Space Between Flange T2 Reel Thickness Rev. 1.20 HT6010/HT6012/HT6014 Dimensions in mm 330 1.0 62 1.5 13.0+0.5 0.2 2.0 0.5 24.8+0.3 0.2 30.2 0.2 11 September 9, 2003 ...
Page 12
... P1 Cavity to Perforation (Length Direction) A0 Cavity Length B0 Cavity Width K0 Cavity Depth t Carrier Tape Thickness C Cover Tape Width Rev. 1.20 HT6010/HT6012/HT6014 Dimensions in mm 24.0+0.3 0.1 12.0 0.1 1.75 0.1 11.5 0.1 1.5+0.1 1.5+0.25 4.0 0.1 2.0 0.1 10.8 0.1 13.3 0.1 3.2 0.1 ...
Page 13
... Holtek s products are not authorized for use as critical components in life support devices or systems. Holtek reserves the right to alter its products without prior notification. For the most up-to-date information, please visit our web site at http://www.holtek.com.tw. Rev. 1.20 HT6010/HT6012/HT6014 13 September 9, 2003 ...