HCS300-I/P Microchip Technology, HCS300-I/P Datasheet - Page 7

• Manufacturer Part Number: HCS300-I/P
• Description: IC,Remote-Control Transmitter/Encoder,CMOS,DIP,8PIN
• Manufacturer: Microchip Technology
• Type: Code Hopping Encoderr

Specifications of HCS300-I/P

• Applications: Remote Secure Access, Keyless Entry
• Mounting Type: Through Hole
• Package / Case: 8-DIP (0.300", 7.62mm)
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

3.6
The Configuration Word is a 16-bit word stored in
EEPROM array that is used by the device to store
information used during the encryption process, as well
as the status of option configurations. The following
sections further explain these bits.
TABLE 3-2:
3.6.1
The discrimination value aids the post-decryption
check on the decoder end. It may be any value, but in
a typical system it will be programmed as the 12 Least
Significant bits of the serial number. Values other than
this must be separately stored by the receiver when a
transmitter is learned. The discrimination bits are part
of the information that form the encrypted portion of
the transmission (Figure 4-2). After the receiver has
decrypted a transmission, the discrimination bits are
checked against the receiver’s stored value to verify
that the decryption process was valid. If the discrimi-
nation value was programmed as the 12 LSb’s of the
serial number then it may merely be compared to the
respective bits of the received serial number; saving
EEPROM space.
3.6.2
The overflow bits are used to extend the number of
possible synchronization values. The synchronization
counter is 16 bits in length, yielding 65,536 values
before the cycle repeats. Under typical use of
10 operations a day, this will provide nearly 18 years of
use before a repeated value will be used. Should the
system designer conclude that is not adequate, then
the overflow bits can be utilized to extend the number
Bit Number
2001 Microchip Technology Inc.
10
11
12
13
14
15
0
1
2
3
4
5
6
7
8
9
CONFIG (Configuration Word)
DISCRIMINATION VALUE
(DISC0 TO DISC9)
OVERFLOW BITS
(OVR0, OVR1)
Discrimination Bit 0
Discrimination Bit 1
Discrimination Bit 2
Discrimination Bit 3
Discrimination Bit 4
Discrimination Bit 5
Discrimination Bit 6
Discrimination Bit 7
Discrimination Bit 8
Discrimination Bit 9
Overflow Bit 0 (OVR0)
Overflow Bit 1 (OVR1)
Low Voltage Trip Point Select (V
SEL
Baud rate Select Bit 0 (BSL0)
Baud rate Select Bit 1 (BSL1)
Reserved, set to 0
CONFIGURATION WORD
)
Bit Description
LOW
of unique values. This can be done by programming
OVR0 and OVR1 to 1s at the time of production. The
encoder will automatically clear OVR0 the first time that
the synchronization value wraps from 0xFFFF to
0x0000 and clear OVR1 the second time the counter
wraps. Once cleared, OVR0 and OVR1 cannot be set
again, thereby creating a permanent record of the
counter overflow. This prevents fast cycling of 64K
counter. If the decoder system is programmed to track
the overflow bits, then the effective number of unique
synchronization values can be extended to 196,608.
3.6.3
BSL0 and BSL1 select the speed of transmission and
the code word blanking. Table 3-3 shows how the bits
are used to select the different baud rates and
Section 5.7 provides detailed explanation in code word
blanking.
TABLE 3-3:
3.6.4
The low voltage trip point select bit is used to tell the
HCS300 what
will be used by the device to determine when to send
the voltage low signal to the receiver. When this bit is
set to a one, the
from a 5V or 6V
V
FIGURE 3-1:
DD
BSL1
Volts (V)
0
0
1
1
level is assumed to be 3.0 volts.
BSL0
4.2
4.0
2.6
2.2
2.0
1.8
1.6
1.4
3.8
3.6
2.4
(BSL0, BSL1)
LOW VOLTAGE TRIP POINT
SELECT (V
BAUD RATE SELECT BITS
0
1
0
1
V
-40
DD
V
V
DD
BAUD RATE SELECT
DD
level is being used. This information
Basic Pulse
level. If the bit is set low, then the
level is assumed to be operating
Element
V
400 s
200 s
100 s
100 s
LOW
LOW SEL
0
V
V
CHARACTERISTICS
LOW
LOW
HCS300
)
sel = 1
sel = 0
50
DS21137F-page 7
Code Words
Transmitted
1 out of 2
1 out of 2
1 out of 4
85
All
Temp (C)
V
LOW