DSPIC30F3010-20E/ML Microchip Technology, DSPIC30F3010-20E/ML Datasheet - Page 19
![IC,DSP,16-BIT,CMOS,LLCC,44PIN,PLASTIC](/photos/6/81/68122/150-44-qfn_sml.jpg)
DSPIC30F3010-20E/ML
Manufacturer Part Number
DSPIC30F3010-20E/ML
Description
IC,DSP,16-BIT,CMOS,LLCC,44PIN,PLASTIC
Manufacturer
Microchip Technology
Series
dsPIC™ 30Fr
Datasheets
1.DSPIC30F2011-20ISO.pdf
(66 pages)
2.DSPIC30F2011-20IP.pdf
(26 pages)
3.DSPIC30F3010-30ISO.pdf
(228 pages)
4.DSPIC30F3010-30ISO.pdf
(18 pages)
5.DSPIC30F3010-30ISO.pdf
(6 pages)
6.DSPIC30F3010-30ISO.pdf
(16 pages)
7.DSPIC30F3010-30ISO.pdf
(22 pages)
Specifications of DSPIC30F3010-20E/ML
Rohs Compliant
YES
Core Processor
dsPIC
Core Size
16-Bit
Speed
20 MIPS
Connectivity
I²C, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, Motor Control PWM, QEI, POR, PWM, WDT
Number Of I /o
20
Program Memory Size
24KB (8K x 24)
Program Memory Type
FLASH
Eeprom Size
1K x 8
Ram Size
1K x 8
Voltage - Supply (vcc/vdd)
2.5 V ~ 5.5 V
Data Converters
A/D 6x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 125°C
Package / Case
44-QFN
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
XLT44QFN4 - SOCKET TRANS ICE 28DIP TO 44QFN
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
35.3.3.4
Figure 35-13: SPI Slave, Frame Master Connection Diagram
35.3.3.5
Figure 35-14: SPI Slave, Frame Slave Connection Diagram
© 2008 Microchip Technology Inc.
SPI Slave, Frame Master Mode
SPI Slave, Frame Slave Mode
(SPI1 Slave, Framed Master)
(SPI1 Slave, Framed Slave)
Section 35. Serial Peripheral Interface (SPI) (Part II)
In the SPI Slave/Frame Master mode, the module acts as the SPI slave and takes its clock from
the other SPI module; however, it produces frame synchronization signals to control data
transmission (Figure 35-13). This mode is enabled by setting the MSTEN bit to ‘0’, the FRMEN
bit to ‘1’ and the SPIFSD bit to ‘0’.
The input SPI clock will be continuous in Slave mode. The SS1 pin will be an output when the
SPIFSD bit is low. Therefore, when the SPI1BUF is written, the module drives the SS1 pin to the
active state on the appropriate transmit edge of the SPI clock for one SPI clock cycle. Data will
start transmitting on the appropriate SPI clock transmit edge.
In the SPI Slave/Frame Slave mode, the module obtains both its clock and frame synchronization
signal from the Master module (Figure 35-14). This mode is enabled by setting MSTEN to ‘0’,
FRMEN to ‘1’ and SPIFSD to ‘1’.
In this mode, both the SCK1 and SS1 pins will be inputs. The SS1 pin is sampled on the sample
edge of the SPI clock. When SS1 is sampled at its active state, data will be transmitted on the
appropriate transmit edge of SCK1.
dsPIC30F
dsPIC30F
SDO1
SCK1
SDO1
SCK1
SDI1
SDI1
SS1
SS1
Frame Synchronization
Pulse
Frame Synchronization
Pulse
Serial Clock
Serial Clock
SDI1
SDO1
SCK1
SS1
SDI1
SDO1
SCK1
SS1
PROCESSOR 2
PROCESSOR 2
DS70272B-page 35-19
35