DSPIC30F3013-20E/SO Microchip Technology, DSPIC30F3013-20E/SO Datasheet
DSPIC30F3013-20E/SO
Specifications of DSPIC30F3013-20E/SO
Related parts for DSPIC30F3013-20E/SO
DSPIC30F3013-20E/SO Summary of contents
Page 1
... Microchip corporate web site (www.microchip.com). TABLE 1: SILICON DEVREV VALUES Part Number dsPIC30F3012 dsPIC30F3013 Note 1: The Device and Revision IDs (DEVID and DEVREV) are located at the last two implemented addresses in program memory. 2: Refer to the “dsPIC30F Flash Programming Specification” (DS70102) for detailed information on Device and Revision IDs for your specific device. © ...
Page 2
... The PLL LOCK Status bit (OSCCON<5>) can occasionally get cleared and generate an oscillator failure trap even when the PLL is still locked and functioning correctly. An address error trap occurs in certain addressing modes when accessing the first four bytes of any PSV page. Affected (1) Revisions devices, the © 2010 Microchip Technology Inc. ...
Page 3
... Mode Note 1: Only those issues indicated in the last column apply to the current silicon revision. © 2010 Microchip Technology Inc. Issue Summary The 10-bit slave does not set the RBF flag or load the I2CxRCV register, on address match if the Least Significant bits (LSbs) of the address are the same as the 7-bit reserved addresses ...
Page 4
... BCD number MOV.b #0x80, w1 ;Second BCD number ADD.b w0, w1, w2 ;Perform addition BRA NC, L0 ;If C set DAW.b w2 ;If not,do DAW and BSET.b SR, #C ;set the carry bit BRA L1 ;and exit L0:DAW.b w2 L1: .... Affected Silicon Revisions © 2010 Microchip Technology Inc. ...
Page 5
... RAM register before performing the operations listed in Table 3. Example 3 demonstrates the work around for Example 2. © 2010 Microchip Technology Inc. dsPIC30F3012/3013 These instructions are identified in Table 3. Example 2 demonstrates one scenario in which this occurs. ...
Page 6
... DISI state. For temporarily modifying and restoring the CPU IPL, the mac- ros RESTORE_CPU_IPL can be used, as shown in Example 7. These macros also make use of the SET_CPU_IPL macro. USING DISI USING SET_CPU_IPL MACRO \ \ and SET_AND_SAVE_CPU_IPL © 2010 Microchip Technology Inc. ...
Page 7
... SET_AND_SAVE_CPU_IPL (save_sr, 7);\ x; \ RESTORE_CPU_IPL (save_sr); } (void INTERRUPT_PROTECT (IEC0bits.U1TXIE=0); Note: If you are using a MPLAB C30 compiler version earlier than version 1.32, you may still use the macros by adding them to your application. Affected Silicon Revisions © 2010 Microchip Technology Inc. dsPIC30F3012/3013 DS80448D-page 7 ...
Page 8
... CY Work around None. However, the user may use a timer interrupt and write to the associated PORT register to control the pin manually. Affected Silicon Revisions © 2010 Microchip Technology Inc ...
Page 9
... Module: PLL PLL mode is used, the input frequency range is 5 MHz-10 MHz instead of 4 MHz-10 MHz. Work around None PLL mode is used, make sure the input crystal or clock frequency is 5 MHz or greater. Affected Silicon Revisions © 2010 Microchip Technology Inc. dsPIC30F3012/3013 DS80448D-page 9 ...
Page 10
... GotoSleep( ) function call. This ensures that the device continues executing the correct code sequence after waking up from Sleep mode. Example 9 described above. ; Ensure flag is reset ; Return from Interrupt Service Routine the function call would be demonstrates the work around © 2010 Microchip Technology Inc. ...
Page 11
... Note: The above work around is recommended for users for whom application hardware changes are not possible. © 2010 Microchip Technology Inc. dsPIC30F3012/3013 Work around 3: Instead of executing a PWRSAV #0 instruction to put the device into Sleep mode, perform a clock switch to the 32 kHz Low-Power (LP) Oscillator with a 64:1 postscaler mode ...
Page 12
... If the D_A flag and the I2COV flag are both set, a valid data byte was received and a previous valid data byte was lost. It will be necessary to code for handling this overflow condition. Affected Silicon Revisions © 2010 Microchip Technology Inc slave interrupt 2 C nodes receive 2 C data 2 C nodes ...
Page 13
... Affected Silicon Revisions © 2010 Microchip Technology Inc. dsPIC30F3012/3013 16. Module: PLL The PLL LOCK Status bit (OSCCON<5>) can occasionally get cleared and generate an oscillator failure trap even when the PLL is still locked and functioning correctly. ...
Page 14
... C bus, and can cause 2 C module are set to values ‘1’ and 2 C module and the first data 2 C masters should be synchro module to be initialized 2 C module is with other modules that have 2 C module module. © 2010 Microchip Technology Inc. ...
Page 15
... BSET.b [w1], #6;set poscalar to divide by 4 Affected Silicon Revisions © 2010 Microchip Technology Inc. dsPIC30F3012/3013 23. Module: OSC2 Pin The port pin, RC15, is multiplexed with the primary oscillator pin, OSC2. When pin RC15 is required for digital input/output, specific bits in the Oscillator ...
Page 16
... Standard Operating Conditions: 3.3V and 5.0V (±10%) (unless otherwise stated) Operating temperature Min Typ Max V — 0.8 SS 2.1 — -40°C ≤ T ≤ +85°C for Industrial A -40°C ≤ T ≤ +125°C for Extended A Units Conditions V SMbus enabled V SMbus enabled © 2010 Microchip Technology Inc. ...
Page 17
... Rev B Document (8/2009) Updated silicon issue 5 (Interrupt Controller). Rev C Document (1/2010) Updated silicon issue 5 (Interrupt Controller). Rev D Document (6/2010) Added silicon issue 24 (ADC) and data sheet clarification 1 (DC Characteristics: I/O Pin Input Specifications). © 2010 Microchip Technology Inc. 2 C), 21 (32 kHz dsPIC30F3012/3013 DS80448D-page 17 ...
Page 18
... NOTES: DS80448D-page 18 © 2010 Microchip Technology Inc. ...
Page 19
... PICtail, REAL ICE, rfLAB, Select Mode, Total Endurance, TSHARC, UniWinDriver, WiperLock and ZENA are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. SQTP is a service mark of Microchip Technology Incorporated in the U.S.A. All other trademarks mentioned herein are property of their respective companies. ...
Page 20
... Philippines - Manila Tel: 63-2-634-9065 Fax: 63-2-634-9069 Singapore Tel: 65-6334-8870 Fax: 65-6334-8850 Taiwan - Hsin Chu Tel: 886-3-6578-300 Fax: 886-3-6578-370 Taiwan - Kaohsiung Tel: 886-7-536-4818 Fax: 886-7-536-4803 Taiwan - Taipei Tel: 886-2-2500-6610 Fax: 886-2-2508-0102 Thailand - Bangkok Tel: 66-2-694-1351 Fax: 66-2-694-1350 © 2010 Microchip Technology Inc. 01/05/10 ...