ISL5586FCM Intersil, ISL5586FCM Datasheet
ISL5586FCM
Specifications of ISL5586FCM
Available stocks
Related parts for ISL5586FCM
ISL5586FCM Summary of contents
Page 1
... CURRENT LIMIT INTERNAL DETECTOR LOGIC RTD RD DET CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 321-724-7143 RSLIC18™ trademark of Intersil Corporation. All other trademarks mentioned are the property of their respective owners. ISL5586 FN4924.2 V RINGING RSP PORT V RSM V ...
Page 2
... Ordering Information HIGH BATTERY (V PART NUMBER 100V 85V ISL5586FCM ISL5586FCMZ (Note) ISL5586FCMZ-T (Note) ISL5586BIM ISL5586BIMZ (Note) • ISL5586CIM • ISL5586CIMZ (Note) ISL5586DIM ISL5586DIMZ (Note) NOTE: Intersil Pb-free products employ special Pb-free material sets; molding compounds/die attach materials and 100% matte tin plate termination finish, which are RoHS compliant and compatible with both SnPb and Pb-free soldering operations ...
Page 3
Absolute Maximum Ratings Maximum Supply Voltages ...
Page 4
Electrical Specifications Unless Otherwise Specified, T loop current limit = 25mA. All AC Parameters are specified at 600 frequency band of 300Hz to 3.4kHz. Protection resistors = 0 product offering. (Continued) PARAMETER Amplitude Tracking, Off Hook, 2-Wire to 4-Wire, 4-Wire ...
Page 5
Electrical Specifications Unless Otherwise Specified, T loop current limit = 25mA. All AC Parameters are specified at 600 frequency band of 300Hz to 3.4kHz. Protection resistors = 0 product offering. (Continued) PARAMETER Forward Active, BSEL = 2.0V -100V ...
Page 6
Electrical Specifications Unless Otherwise Specified, T loop current limit = 25mA. All AC Parameters are specified at 600 frequency band of 300Hz to 3.4kHz. Protection resistors = 0 product offering. (Continued) PARAMETER V to 4-Wire, BSEL = 2.0V BH NOTES: ...
Page 7
133 RP1 – – RP2 + 4-WIRE TO 2-WIRE GAIN The 4-wire to 2-wire gain ( defined as the receive 42 gain ...
Page 8
To allow for proper ring trip operation, the transient current limit setting should be set at least 25% higher than the peak ring trip current setting. Setting the transient current 25% higher should account for programming tolerances of both the ...
Page 9
The quiescent current terms are specified in the electrical tables for each operating mode. Load power dissipation is not a factor since this hook mode. Some applications may specify a standby current. The standby current may be ...
Page 10
LIM 2R (Ω LOOP FIGURE 6. I VERSUS R LOAD CHARACTERISTIC LOOP LOOP The slope of the feed characteristic and the battery voltage define the maximum loop current on the shortest possible loop as ...
Page 11
I 1 75kΩ FIGURE 7. REVERSAL TIMING CONTROL Power Dissipation The power dissipation equations for forward active operation also apply to the reverse active mode. Ringing Overview The Ringing mode (RNG, 100) provides linear amplification to support a ...
Page 12
The terms t and t represent the cadence. The ringing R S interval is t and the silent interval ratio 1: The quiescent power of the device in the Ringing mode is ...
Page 13
Power Denial Overview The power denial mode (111) will shutdown the entire device except for the logic interface. Loop supervision is not provided. This mode may be used as a sleep mode or to shut down the SLIC in the ...
Page 14
Impedance and Gain Derivations The feedback mechanism for monitoring the AC portion of the loop current consists of two amplifiers, the sense amplifier (SA) and the transmit amplifier (TA). The AC feedback signal is used for impedance synthesis. A detailed ...
Page 15
FIGURE 12. SCHEMATIC FOR 4-WIRE TO 2-WIRE GAIN DERIVATION Note that in Figure 13 referenced on the line side of the TR protection resistors. On the ...
Page 16
Equations 48 and 60 can be combined to re-write the 4-wire to 4-wire gain equation. Z TX4W × 2.8 ----------------------------------------- - ------ ------------------- - = – ...
Page 17
Pin Descriptions PLCC SYMBOL 1 TIP TIP Power Amplifier Output. 2 BGND Battery Ground - To be connected to zero potential. All loop current and longitudinal current flow from this ground. Internally separate from AGND and SGND but should be ...
Page 18
Basic Application Circuit D 1 F1250T TIP B1100CC RING RTD B1100CC F1250T R IL ILIM CDCM C DC CDCP C ...
Page 19
TABLE 2. BASIC APPLICATION CIRCUIT COMPONENT LIST COMPONENT U1 - Ringing SLIC POL SH CFB ...
Page 20
... Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use ...