LM87CIMT National Semiconductor, LM87CIMT Datasheet - Page 13

• Manufacturer Part Number: LM87CIMT
• Description: Temperature Sensor IC
• Manufacturer: National Semiconductor

Specifications of LM87CIMT

• Peak Reflow Compatible (260 C): No
• Ic Function: Temperature Sensor IC
• Supply Voltage Max: 3.8V
• Leaded Process Compatible: No
• Mounting Type: Surface Mount
• Operating Temperature Range: -40°C To +125°C
• Temperature Sensor Function: Temp Sensor
• Interface Type: Serial (2-Wire)
• Output Type: Digital
• Package Type: TSSOP
• Operating Temperature (min): -40C
• Operating Temperature (max): 125C
• Operating Temperature Classification: Automotive
• Operating Supply Voltage (typ): 3.3V
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

All of these communications are depicted in the Serial Bus
Interface Timing Diagrams as shown in
ple shown corresponds to the ADD pin tied to Vcc, so XY=01
and the resulting LM87 address is 0101101.
Serial Bus Timeout can be initiated by holding the SMBCLK
line low for greater than t
3.0 USING THE LM87
3.1 Power On
When power is first applied, the LM87 performs a “power on
reset” on several of its registers. The power on condition of
the LM87's registers is shown in
power on values are not shown have power on conditions that
are indeterminate (this includes the value RAM ,exclusive of
the DAC data, and WATCHDOG limits). When power is first
applied the ADC is inactive. In most applications, the first ac-
tion after power on is to write WATCHDOG limits into the
Value RAM.
3.2 Resets
All register values, except the Programmed DAC Output can
be returned to their "power on" default values by taking the
RESET# input low for at least TBD ns or by performing a
Configuration Register INITIALIZATION. The Value RAM
conversion results, and Value RAM WATCHDOG limits are
not Reset and will be indeterminate immediately after power
on. If the Value RAM contains valid conversion results and/or
Value RAM WATCHDOG limits have been previously set,
they will not be affected by a Configuration Register INITIAL-
IZATION. The Power On Reset, RESET# input, and Config-
uration Register INITIALIZATION, clear or initialize the
following registers (the initialized values are shown on Table
I). Power On Reset also sets the Programmed DAC Output
to full scale (FFh) Hardware High Limit registers 13h, and 14h
will only be returned to default values if the "Write Once" bits
in Configuration Register 2 have not been set:
•
•
•
•
•
•
•
•
•
•
•
•
•
Configuration Register INITIALIZATION is accomplished by
setting Bit 7 of Configuration Register 1 high. This bit auto-
matically clears after being set.
3.3 Configuration Registers and Channel Mode Register
The Configuration Registers and Channel Mode Register
control the LM87 operation. At power on, the ADC is stopped
and INT_Clear is asserted, clearing the INT# hardwire output.
These registers start and stop the LM87, enable and disable
interrupt output, configure the operation of dual function in-
puts, and provide the Reset functions described in Section
3.2.
Bit 0 of Configuration Register 1 controls the monitoring loop
of the LM87. Setting Bit 0 low stops the LM87 monitoring loop
and puts the LM87 in shutdown mode, reducing power con-
sumption. Serial Bus communication can take place with any
Configuration Registers 1 and 2
Channel Mode Register
Hardware High Limit Registers
Interrupt Status Register 1
Interrupt Status Register 2
Interrupt Status Mirror Register 1
Interrupt Status Mirror Register 2
Interrupt Mask Register 1
Interrupt Mask Register 2
Chassis Intrusion Clear Register
VID/Fan Divisor Register
VID4 Register
Extended Mode Register
TIMEOUT
Table 1
(35 ms max). Serial Bus
Figure
Registers whose
5. The exam-
13
Timeout resets the serial bus interface circuitry to the idle
state and readies the LM87 for a new serial bus communica-
tion.
register in the LM87 although activity on the SMBData and
SMBCLK lines will increase shutdown current, up to as much
as maximum rated supply current, while the activity takes
place. Taking Bit 0 high starts the monitoring loop, described
in more detail subsequently.
Bit 1 of Configuration Register 1 enables the INT# Interrupt
output when this bit is taken high.
Bit 2 of Configuration Register 1 enables the THERM# Inter-
rupt output when this bit is taken high.
Bit 3 of Configuration Register 1 clears the INT# output when
set high, without affecting the contents of the Interrupt Status
Registers. The LM87 will stop monitoring. It will resume upon
clearing of this bit.
Bit 4 of Configuration Register 1 provides an active low 20 ms
(minimum) pulse at the RESET# output when set high.
Bit 6 of Configuration Register 1 clears the THERM# output
when set high, without affecting the contents of the Interrupt
Status Registers.
Bit 7 of Configuration Register 1 (the INITIALIZATION bit) re-
sets the internal registers of the LM87 as described in Section
3.2.
Bit 7 of the CI_Clear Register provides an active low 20 ms
(minimum) pulse at the CI# output pin when set high. This is
intended for resetting the Chassis Intrusion circuitry.
Bit 0 of Configuration Register 2 enables the INT# Interrupt
output for THERM# events when set low. When this bit is set
high, THERM# error events will not affect the INT# output.
Bit 1 of Configuration Register 2 locks the value set in the
Internal Temperature high limit register at 13h. The value
cannot be changed until a Power On Reset is performed.
Bit 2 of Configuration Register 2 locks the value set in the
External Temperature high limit register at 14h. The value
cannot be changed until a Power On Reset is performed.
Bit 3 of Configuration Register 2 sets the THERM# output
mode. When set to 0, the THERM# output functions in default
mode, when set to 1, THERM# operates in ACPI mode.
Bit 6 of Configuration Register 2, when set to 1, enables pin
21 as an active high (IRQ3) interrupt input. When set to 0, this
input is disabled as an IRQ interrupt.
Bit 7 of Configuration Register 2, when set to 1, enables pin
20 as an active high (IRQ4) interrupt input. When set to 0, this
input is disabled as an IRQ interrupt.
Bit 0 of the Channel Mode Register, when set to 1, configures
pin 5 as AIN1. When set to 0, pin 5 is configured as the FAN1
input.
Bit 1 of the Channel Mode Register, when set to 1, configures
pin 6 as AIN2. When set to 0, pin 6 is configured as the FAN2
input.
Bit 2 of the Channel Mode Register, when set to 0, configures
pins 18 and 19 as +2.5V and V
to 1, pins 18 and 19 are configured as a second remote tem-
perature sensing channel.
Bit 3 of the Channel Mode Register, when set to 0, sets the
nominal voltage for internal V
set to 1, the nominal V
CC
range is 5V.
CC
CCP2
measurement to 3.3V. When
voltage inputs. When set
www.national.com