PIC16F870-E/SO Microchip Technology, PIC16F870-E/SO Datasheet - Page 90

• Manufacturer Part Number: PIC16F870-E/SO
• Description: 28 PIN, 3.5KB ENH FLASH, 128 RAM, 22 I/O,
• Manufacturer: Microchip Technology
• Series: PIC® 16Fr

Specifications of PIC16F870-E/SO

• Rohs Compliant: YES
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 22
• Program Memory Size: 3.5KB (2K x 14)
• Program Memory Type: FLASH
• Eeprom Size: 64 x 8
• Ram Size: 128 x 8
• Voltage - Supply (vcc/vdd): 4 V ~ 5.5 V
• Data Converters: A/D 5x10b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 28-SOIC (7.5mm Width)
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: I3-DB16F871 - BOARD DAUGHTER ICEPIC3
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

PIC16F870/871
REGISTER 11-1:
DS30569B-page 88
bit 13
bit 13-12,
bit 5-4
bit 11
bit 10
bit 9
bit 8
bit 7
bit 6
bit 3
bit 2
bit 1-0
CP1
Note 1: The erased (unprogrammed) value of the configuration word is 3FFFh.
2: All of the CP1:CP0 pairs have to be given the same value to enable the code protection scheme listed.
3: Enabling Brown-out Reset automatically enables Power-up Timer (PWRT), regardless of the value of bit
CP0
PWRTEN. Ensure the Power-up Timer is enabled any time Brown-out Reset is enabled.
CP1:CP0: FLASH Program Memory Code Protection bits
11 = Code protection off
10 = Not supported
01 = Not supported
00 = Code protection on
DEBUG: In-Circuit Debugger Mode
1 = In-Circuit Debugger disabled, RB6 and RB7 are general purpose I/O pins
0 = In-Circuit Debugger enabled, RB6 and RB7 are dedicated to the debugger
Unimplemented: Read as ‘1’
WRT: FLASH Program Memory Write Enable
1 = Unprotected program memory may be written to by EECON control
0 = Unprotected program memory may not be written to by EECON control
CPD: Data EE Memory Code Protection
1 = Code protection off
0 = Data EEPROM memory code protected
LVP: Low Voltage In-Circuit Serial Programming Enable bit
1 = RB3/PGM pin has PGM function, low voltage programming enabled
0 = RB3 is digital I/O, HV on MCLR must be used for programming
BOREN: Brown-out Reset Enable bit
1 = BOR enabled
0 = BOR disabled
PWRTEN: Power-up Timer Enable bit
1 = PWRT disabled
0 = PWRT enabled
WDTEN: Watchdog Timer Enable bit
1 = WDT enabled
0 = WDT disabled
FOSC1:FOSC0: Oscillator Selection bits
11 = RC oscillator
10 = HS oscillator
01 = XT oscillator
00 = LP oscillator
Legend:
R = Readable bit
- n = Value at POR
DEBUG
CONFIGURATION WORD (ADDRESS 2007h)
—
WRT CPD LVP BOREN
W = Writable bit
‘1’ = Bit is set
(3)
(3)
CP1
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
CP0 PWRTEN WDTEN FOSC1 FOSC0
(2)
(1)
 2003 Microchip Technology Inc.
x = Bit is unknown
bit 0