PIC24FJ64GA006T-I/PT Microchip Technology, PIC24FJ64GA006T-I/PT Datasheet - Page 10

• Manufacturer Part Number: PIC24FJ64GA006T-I/PT
• Description: Microcontroller
• Manufacturer: Microchip Technology
• Series: PIC® 24Fr

Specifications of PIC24FJ64GA006T-I/PT

• Core Processor: PIC
• Core Size: 16-Bit
• Speed: 16MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 53
• Program Memory Size: 64KB (22K x 24)
• Program Memory Type: FLASH
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 16x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-TFQFP
• Processor Series: PIC24FJ
• Core: PIC
• Data Bus Width: 16 bit
• Data Ram Size: 8 KB
• Interface Type: I2C, SPI, UART
• Maximum Clock Frequency: 32 MHz
• Number Of Programmable I/os: 53
• Number Of Timers: 5
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52713-733, 52714-737, 53276-922, EWDSPIC
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, DM240011, DV164033, MA240013, AC164127, DM240001
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 16 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: DM240011 - KIT STARTER MPLAB FOR PIC24F MCUDV164033 - KIT START EXPLORER 16 MPLAB ICD2MA160011 - DAUGHTER BOARD PICDEM LCD 16F91XDM240001 - BOARD DEMO PIC24/DSPIC33/PIC32AC164327 - MODULE SKT FOR 64TQFP
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

PIC24FJ128GA010 FAMILY
25. Module: UART (Auto-Baud)
26. Module: Interrupts (Traps)
27. Module: Output Compare
DS80471A-page 10
With the auto-baud feature selected, the Sync
Break character (0x55) may be loaded into the
FIFO as data.
Work around
To prevent the Sync Break character from being
loaded into the FIFO, load the UxBRG register with
either 0x0000 or 0xFFFF prior to enabling the
auto-baud feature (ABAUD = 1).
Affected Silicon Revisions
The device may not exit Doze mode if certain trap
conditions occur. Address error, stack error and
math error traps are affected. Oscillator failure and
all interrupt sources are not affected and can
cause the device to correctly exit Doze mode.
Work around
None.
Affected Silicon Revisions
The output compare module may output a single
glitch for one T
(OCM<2:0> = 000). This issue occurs when the
output state of the associated Data Latch register
(LATx) is in the opposite state of the Output Com-
pare mode when the peripheral is enabled. It can
also occur when switching between two Output
Compare modes with opposite output states.
Work around
If the output glitch must be avoided, verify that the
associated data latch value of the OCx pin matches
the initial state of the desired Output Compare
mode. For example, if Output Compare 5 is
configured for mode, OCM<2:0> = 001, ensure that
the LATD<4> bit is clear prior to writing the OCM
bits. The port latch output value will match the initial
output state of the OC5 pin and avoid the glitch
when the peripheral is enabled.
Affected Silicon Revisions
A2
A2
A2
X
X
X
A3
A3
A3
X
X
X
A4
A4
A4
X
X
X
CY
after the module is enabled
C1
C1
C1
C2
C2
C2
28. Module: A/D (INT0 Trigger)
29. Module: SPI (Framed Modes)
With the External Interrupt 0 (INT0) selected to start
an A/D conversion (SSRC<2:0> = 001), the device
may not wake-up from Sleep or Idle mode if more
than one conversion is selected per interrupt
(SMPI<3:0> <> 0000). Interrupts are generated
correctly if the device is not in a Sleep or Idle mode.
Work around
Configure the A/D to generate an interrupt after
every
another wake-up source, such as the WDT or
another interrupt source, to exit the Sleep or Idle
mode. Alternatively, perform A/D conversions in
Run mode.
Affected Silicon Revisions
A frame synchronization pulse may not be output
in SPI Master mode if the pulse is selected to
coincide with the first bit clock (SPIFE = 1). SCKx
and SDOx waveforms are not affected.
Work around
Select the frame synchronization pulses to
precede the first bit clock (SPIFE = 0). The frame
pulses will output correctly as described in the
product data sheet.
Affected Silicon Revisions
A2
A2
X
X
A3
A3
conversion
X
X
A4
A4
X
X
© 2009 Microchip Technology Inc.
C1
C1
(SMPI<3:0> = 0000).
C2
C2
Use