A1182ELHLT Allegro Microsystems Inc, A1182ELHLT Datasheet - Page 12

• Manufacturer Part Number: A1182ELHLT
• Description: IC SWITCH HALL EFFECT UNI SOT-23
• Manufacturer: Allegro Microsystems Inc
• Type: Unipolar Switchr

Specifications of A1182ELHLT

• Sensing Range: 60G ~ 200G Trip - Programmable, Fixed Release
• Voltage - Supply: 3.5 V ~ 24 V
• Current - Supply: 6.9mA
• Output Type: Digital, Open Collector
• Features: Programmable
• Operating Temperature: -40°C ~ 85°C
• Package / Case: SOT-23W
• Magnetic Type: Unipolar
• Operating Supply Voltage (min): 3.5V
• Operating Supply Voltage (typ): 5/9/12/15/18V
• Operating Supply Voltage (max): 24V
• Mag Sensor Operate Point (g): 200Gs
• Mag Sensor Hysteresis(g): 15Gs
• Package Type: SOT-23W
• Pin Count: 3
• Mounting: Surface Mount
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Current - Output (max): -
• Lead Free Status / RoHS Status: Not Compliant, Contains lead / RoHS non-compliant

A1180, A1181,
A1182,
Programming Protocol
The operate switchpoint, B
so, a coded series of voltage pulses through the VCC pin is used
to set bitfi elds in onboard registers. The effect on the device
output can be monitored, and the registers can be cleared and
set repeatedly until the required B
setting permanent, bitfi eld-level solid state fuses are blown, and
fi nally, a device-level fuse is blown, blocking any further cod-
ing. It is not necessary to program the release switchpoint, B
because the difference between B
hysteresis, B
The range of values between B
31 increments. The actual change in magnetic fl ux (G) repre-
sented by each increment is indicated by B
Characteristics table; however, testing is the only method for
verifying the resulting B
ments are individually identifi ed using 5 data bits, which are
physically represented by 5 bitfi elds in the onboard registers.
By setting these bitfi elds, the corresponding calibration value is
programmed into the device.
Three voltage levels are used in programming the device: a low
voltage, V
mid-level voltage, V
in the device; and a high voltage, V
V
long in duration). A fourth voltage level, essentially 0 V, is used
to clear the registers between pulse sequences. The pulse values
are shown in the Programming Protocol Characteristics table and
in fi gure 4.
PROGRAMMING PROTOCOL CHARACTERISTICS, over operating temperature range, unless otherwise noted
Programming Voltage
Programming Current
Pulse Width
Pulse Rise Time
Pulse Fall Time
1
2
provide the current necessary to blow the fuse.
Programming voltages are measured at the VCC pin.
A bypass capacitor with a minimum capacitance of 0.1 μF must be connected from VCC to the GND pin of the A118x device in order to
PM
pulses (when short in duration) and to blow fuses (when
Characteristic
PL
and
HYS
, a minimum required to sustain register settings; a
A1183
, is fi xed.
PM
1
2
, used to increment the address counter
OP
). For programming, the 31 incre-
OP
, can be fi eld-programmed. To do
OP(min)
Symbol
OP
OP
Chopper-Stabilized Unipolar Hall Effect Switches
V
PH
V
t
t
t
V
I
d(P)
d(0)
d(1)
and B
PP
PM
t
t
is achieved. To make the
PH
PL
r
f
and B
, used to separate sets of
RP
RES
Minimum voltage range during programming
t
OFF time between programming bits
Pulse duration for enable and addressing
sequences
Pulse duration for fuse blowing
V
V
r
OP(max)
PL
PM
= 11 μs; 5 V → 26 V; C
, referred to as the
(see the Operating
to V
to V
PM
is scaled to
Sensitive Two-Wire Field-Programmable
PL
; V
; V
PL
PH
to V
Test Conditions
to V
RP
PH
,
PL
BYP
Additional information on device programming and program-
ming products is available on www. allegromicro.com. Program-
ming hardware is available for purchase, and programming
software is available free of charge.
Code Programming.
do so, a pulse sequence must be transmitted for each bitfi eld that
is being set to 1. If more than one bitfi eld is being set to 1, all
pulse sequences must be sent, one after the other, without allow-
ing V
The same pulse sequence is used to provisionally set bitfi elds as
is used to permanently set bitfi eld-level fuses. The only differ-
ence is that when provisionally setting bitfi elds, no fuse-blowing
pulse is sent at the end of the pulse sequence.
= 0.1 μF
CC
to fall to zero (which clears the registers).
V
V
V
PH
PM
PL
0
V+
Figure 4. Pulse amplitudes and durations
T
d(1)
Each bitfi eld must be individually set. To
115 Northeast Cutoff
1.508.853.5000; www.allegromicro.com
Allegro MicroSystems, Inc.
Worcester, Massachusetts 01615-0036 U.S.A.
Min.
11.5
25.0
100
4.5
20
20
5
5
-
T
d(P)
T
d(0)
Typ.
12.5
26.0
190
300
5.0
-
-
-
-
Max.
13.5
27.0
100
5.5
t
20
-
-
-
-
Units
mA
μs
μs
μs
μs
μs
V
V
V
11