A1184LUA Allegro Microsystems Inc, A1184LUA Datasheet
![IC SWITCH HALL EFFECT UNI 3-SIP](/photos/31/38/313867/ultraminisip-3_sml.jpg)
A1184LUA
Specifications of A1184LUA
Related parts for A1184LUA
A1184LUA Summary of contents
Page 1
Standard Two-Wire Field-Programmable Chopper-Stabilized These parts are in production but have been determined to be NOT FOR NEW DESIGN. This classification indicates that sale of this device is currently restricted to existing customer applications. The device should not be purchased ...
Page 2
Standard Two-Wire Field-Programmable Chopper-Stabilized Features and Benefits ▪ Chopper stabilization ▫ Low switchpoint drift over operating temperature range ▫ Low sensitivity to stress ▪ Field programmable for optimized switchpoints ▪ On-chip protection ▫ Supply transient protection ▫ Reverse-battery protection ▫ ...
Page 3
... Part Number Packing A1184ELHLT-T 7-in. reel, 3000 pieces/reel A1184EUA-T Bulk, 500 pieces/bag A1184LLHLT-T 7-in. reel, 3000 pieces/reel A1184LUA-T Bulk, 500 pieces/bag 1 Contact Allegro for additional packing options. 2 South (+) magnetic fields must be of sufficient strength. Absolute Maximum Ratings Characteristic Supply Voltage Reverse Supply Voltage ...
Page 4
A1184 ELECTRICAL CHARACTERISTICS Characteristic Symbol 1 Supply Voltage Supply Current 2 Supply Zener Clamp Voltage V Supply Zener Clamp Current 3 I Z(supply) Reverse Supply Current Output Slew Rate 4 Chopping Frequency Power-On Time 5 Power-On State 6 ...
Page 5
A1184 I versus Ambient Temperature CC(L) at Various Levels of V (A1184 - 100 Ambient Temperature, T Average B Bits versus Ambient Temperature OP (A1184) 700 600 500 400 300 200 100 ...
Page 6
A1184 THERMAL CHARACTERISTICS may require derating at maximum conditions, see application information Characteristic Package Thermal Resistance *Additional thermal information available on Allegro Web site. Standard Two-Wire Field-Programmable Chopper-Stabilized Unipolar Hall Effect Switch Symbol Test Conditions* Package LH, 1-layer PCB with ...
Page 7
A1184 Operation The output the A1184 device switches high after the CC magnetic field at the Hall element exceeds the operate point threshold When the magnetic field is reduced to below the OP release point ...
Page 8
A1184 Chopper Stabilization Technique A limiting factor for switchpoint accuracy when using Hall effect technology is the small signal voltage developed across the Hall element. This voltage is proportionally small relative to the offset that can be produced at the ...
Page 9
A1184 For additional general application information, visit the Allegro MicroSystems Web site at www. allegromicro.com. Typical Application Circuit The A118x family of devices must be protected by an external bypass capacitor connected between the supply, VCC, BYP and ...
Page 10
A1184 Power Derating The device must be operated below the maximum junction temperature of the device Under certain combinations of J(max) peak conditions, reliable operation may require derating sup- plied power or improving the heat dissipation properties of ...
Page 11
A1184 Programming Protocol The operate switchpoint can be field-programmed so, a coded series of voltage pulses through the VCC pin is used to set bitfields in onboard registers. The effect on the device output can ...
Page 12
A1184 The pulse sequences consist of the following groups of pulses enable sequence bitfield address sequence. 3. When permanently setting the bitfield, a long V ing pulse. (Note: Blown bit fuses cannot be reset.) 4. When ...
Page 13
A1184 The first segment of code is a Enabling Addressing Mode. keying sequence used to enable the bitfield addressing mode. As shown in figure 7, this segment consists of one short V one V pulse, and one short V pulse, ...
Page 14
A1184 +0.12 2.98 –0.08 3 +0.10 2.90 –0. 10° REF 0.95 BSC For Reference Only; not for tooling use (reference dwg. 802840) Dimensions in millimeters Dimensions exclusive of mold flash, gate burrs, and dambar protrusions Exact case and ...
Page 15
A1184 4.09 45° +0.08 3.02 –0.05 2.16 MAX 0.51 REF 1 2 15.75 ±0.51 +0.05 0.43 –0.07 Copyright ©2004-2008, Allegro MicroSystems, Inc. Allegro MicroSystems, Inc. reserves the right to make, from time to time, such de par tures from the ...