A1180LLHLT Allegro Microsystems Inc, A1180LLHLT Datasheet
![IC SWITCH HALL EFFECT UNI SOT-23](/photos/19/49/194943/620-sot-23w_sml.jpg)
A1180LLHLT
Specifications of A1180LLHLT
Available stocks
Related parts for A1180LLHLT
A1180LLHLT Summary of contents
Page 1
Sensitive Two-Wire Field-Programmable Chopper-Stabilized These devices are in production, however, they have been deemed Pre-End of Life. These products are approaching end of life. Within a minimum of 6 months, these devices will enter their final, Last Time Buy, order ...
Page 2
Sensitive Two-Wire Field-Programmable Chopper-Stabilized Features and Benefits ▪ Chopper stabilization ▫ Low switchpoint drift over operating temperature range ▫ Low sensitivity to stress ▪ Field programmable for optimized switchpoints ▪ On-chip protection ▫ Supply transient protection ▫ Reverse-battery protection ▫ ...
Page 3
A1180, A1181, A1182, A1183 and Chopper-Stabilized Unipolar Hall Effect Switches Description (continued) wire than the more traditional open-collector output switches. Additionally, the system designer gains inherent diagnostics because output current normally fl ows in either of two narrowly- specifi ed ...
Page 4
A1180, A1181, A1182, A1183 and Chopper-Stabilized Unipolar Hall Effect Switches ELECTRICAL CHARACTERISTICS Characteristic Symbol 1 Supply Voltage Supply Current 2 Supply Zener Clamp Voltage V Supply Zener Clamp Current I Z(supply) Reverse Supply Current Output Slew Rate 3 Chopping Frequency ...
Page 5
A1180, A1181, A1182, A1183 and Chopper-Stabilized Unipolar Hall Effect Switches I versus Ambient Temperature CC(L) at Various Levels of V (A1180, A1181 - 100 Ambient Temperature, T Average B Bits versus Ambient ...
Page 6
A1180, A1181, A1182, A1183 and Chopper-Stabilized Unipolar Hall Effect Switches EMC (Electromagnetic Compatibility) Requirements Sensitive Two-Wire Field-Programmable Device Qualifi cation Program Contact Allegro for information. Contact your local representative for EMC results. Test Name Reference Specifi cation ESD – Human ...
Page 7
A1180, A1181, A1182, A1183 and Chopper-Stabilized Unipolar Hall Effect Switches THERMAL CHARACTERISTICS may require derating at maximum conditions, see application information Characteristic Package Thermal Resistance *Additional thermal information available on Allegro Web site. Sensitive Two-Wire Field-Programmable Symbol Test Conditions* Package ...
Page 8
A1180, A1181, A1182, A1183 and Chopper-Stabilized Unipolar Hall Effect Switches Operation The output the A1180 and A1182 devices switch low CC after the magnetic fi eld at the Hall element exceeds the oper- ate point threshold, B ...
Page 9
A1180, A1181, A1182, A1183 and Chopper-Stabilized Unipolar Hall Effect Switches Chopper Stabilization Technique A limiting factor for switchpoint accuracy when using Hall effect technology is the small signal voltage developed across the Hall element. This voltage is proportionally small relative ...
Page 10
A1180, A1181, A1182, A1183 and Chopper-Stabilized Unipolar Hall Effect Switches For additional general application information, visit the Allegro MicroSystems Web site at www. allegromicro.com. Typical Application Circuit The A118x family of devices must be protected by an external bypass capacitor, ...
Page 11
A1180, A1181, A1182, A1183 and Chopper-Stabilized Unipolar Hall Effect Switches Power Derating The device must be operated below the maximum junction temperature of the device Under certain combinations of J(max) peak conditions, reliable operation may require derating sup- ...
Page 12
A1180, A1181, A1182, A1183 and Chopper-Stabilized Unipolar Hall Effect Switches Programming Protocol The operate switchpoint can be fi eld-programmed so, a coded series of voltage pulses through the VCC pin is used to set bitfi ...
Page 13
A1180, A1181, A1182, A1183 and Chopper-Stabilized Unipolar Hall Effect Switches The pulse sequences consist of the following groups of pulses enable sequence bitfi eld address sequence. 3. When permanently setting the bitfi eld, a long V ...
Page 14
A1180, A1181, A1182, A1183 and Chopper-Stabilized Unipolar Hall Effect Switches The fi rst segment of code is a Enabling Addressing Mode. keying sequence used to enable the bitfi eld addressing mode. As shown in fi gure 7, this segment consists ...
Page 15
A1180, A1181, A1182, A1183 and Chopper-Stabilized Unipolar Hall Effect Switches +0.12 2.98 –0.08 3 +0.10 2.90 –0. 10° REF 0.95 BSC For Reference Only; not for tooling use (reference dwg. 802840) Dimensions in millimeters Dimensions exclusive of mold ...
Page 16
A1180, A1181, A1182, A1183 and Chopper-Stabilized Unipolar Hall Effect Switches 45° +0.08 3.02 –0.05 2.16 MAX 0.51 REF 1 15.75 ±0.51 +0.05 0.43 –0.07 Copyright ©2004-2011, Allegro MicroSystems, Inc. Allegro MicroSystems, Inc. reserves the right to make, from time to ...