A1186LLHLT Allegro Microsystems Inc, A1186LLHLT Datasheet - Page 12
![IC SWITCH HALL EFFECT UNI SOT-23](/photos/19/49/194943/620-sot-23w_sml.jpg)
A1186LLHLT
Manufacturer Part Number
A1186LLHLT
Description
IC SWITCH HALL EFFECT UNI SOT-23
Manufacturer
Allegro Microsystems Inc
Type
Unipolar Switchr
Specifications of A1186LLHLT
Sensing Range
10G ~ 60G Trip - Programmable, Fixed Release
Voltage - Supply
3.5 V ~ 24 V
Current - Supply
6.9mA
Output Type
Digital, Open Collector
Features
Programmable
Operating Temperature
-40°C ~ 150°C
Package / Case
SOT-23W
Magnetic Type
Unipolar
Operating Supply Voltage (min)
3.5V
Operating Supply Voltage (typ)
5/9/12/15/18V
Operating Supply Voltage (max)
24V
Mag Sensor Operate Point (g)
60Gs
Mag Sensor Hysteresis(g)
15Gs
Package Type
SOT-23W
Pin Count
3
Mounting
Surface Mount
Operating Temp Range
-40C to 150C
Operating Temperature Classification
Automotive
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Current - Output (max)
-
Lead Free Status / RoHS Status
Not Compliant, Contains lead / RoHS non-compliant
A1185
A1186
The pulse sequences consist of the following groups of pulses:
1. An enable sequence.
2. A bitfield address sequence.
3. When permanently setting the bitfield, a long V
4. When permanently setting the bitfield, the level of V
Bitfields that are not set are evaluated as zeros. The bitfield-level
fuses for 0 value bitfields are never blown. This prevents inad-
ing pulse. (Note: Blown bit fuses cannot be reset.)
be allowed to drop to zero between each pulse sequence, in
order to clear all registers. However, when provisionally set-
ting bitfields, V
sequences, in order to maintain the prior bitfield settings while
preparing to set additional bitfields.
and
CC
must be maintained at V
V
V
V
V
V
V
PM
PH
PL
PM
PH
PL
0
0
V+
V+
Figure 5. Pulse sequence to provisionally try calibration value 5.
Figure 6. Pulse sequence to permanently encode calibration value 5 (101 binary, or
bitfield address 3 and bitfield address 1).
Chopper-Stabilized Unipolar Hall Effect Switches
Enable
Enable
Ultrasensitive Two-Wire Field-Programmable
PL
between pulse
Try 5
Encode 00100
PH
10
fuse-blow-
Address
Address
CC
2
must
(4
10
)
Blow
Monitoring
Optional
vertently setting the bitfield to 1. Instead, blowing the device-
level fuse protects the 0 bitfields from being accidentally set in
the future.
When provisionally trying the calibration value, one pulse
sequence is used, using decimal values. The sequence for setting
the value 5
When permanently setting values, the bitfields must be set indi-
vidually, and 5
set to 1 (000100
which is 1
sequences for permanently setting the calibration value 5 are
shown in figure 6. The final V
period, enough to blow the corresponding bitfield-level fuse.
Clear
t
10
Enable
10
). Bit 2 is ignored, and so remains 0.Two pulse
is shown in figure 5.
10
Encode 00001
2
, which is 4
must be programmed as binary 101. Bit 3 is
Address
2
Blow
(1
115 Northeast Cutoff
1.508.853.5000; www.allegromicro.com
Allegro MicroSystems, Inc.
Worcester, Massachusetts 01615-0036 U.S.A.
10
)
10
PH
), then bit 1 is set to 1 (000001
pulse is maintained for a longer
t
2
,
11