AD22103KRZ Analog Devices Inc, AD22103KRZ Datasheet - Page 5

• Manufacturer Part Number: AD22103KRZ
• Description: IC TEMP SENSOR 3.3V SGNL 8-SOIC
• Manufacturer: Analog Devices Inc

Specifications of AD22103KRZ

• Sensing Temperature: 0°C ~ 100°C
• Output Type: Voltage
• Voltage - Supply: 2.7 V ~ 3.6 V
• Accuracy: ±0.5°C
• Package / Case: 8-SOIC (0.154", 3.90mm Width)
• Ic Output Type: Voltage
• Sensing Accuracy Range: ± 0.5°C
• Supply Current: 500µA
• Supply Voltage Range: 2.7V To 3.6V
• Resolution (bits): 8bit
• Sensor Case Style: SOIC
• No. Of Pins: 8
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

REV. 0
THERMAL ENVIRONMENT EFFECTS
The thermal environment in which the AD22103 is used deter-
mines two performance traits: the effect of self-heating on accu-
racy and the response time of the sensor to rapid changes in
temperature. In the first case, a rise in the IC junction tempera-
ture above the ambient temperature is a function of two variables;
the power consumption of the AD22103 and the thermal resis-
tance between the chip and the ambient environment
heating error in degrees Celsius can be derived by multiplying
the power dissipation by
widely for surroundings with different heat sinking capacities, it
is necessary to specify
shows how the magnitude of self-heating error varies relative to
the environment. A typical part will dissipate about 1.5 mW at
room temperature with a 3.3 V supply and negligible output
loading. In still air, without a “heat sink,” the table below indi-
cates a
Thermal rise will be considerably less in either moving air or
with direct physical connection to a solid (or liquid) body.
Medium
Aluminum Block
Moving Air**
Still Air
**1200 CFM.
Response of the AD22103 output to abrupt changes in ambient
temperature can be modeled by a single time constant expo-
nential function. Figure 7 shows typical response time plots for
a few media of interest.
The time constant is dependent on
capacities of the chip and the package. Table I lists the effec-
tive (time to reach 63.2% of the final value) for a few different
media. Copper printed circuit board connections were
*The time constant is defined as the time to reach 63.2% of the final
Without Heat Sink
Without Heat Sink
temperature change.
100
JA
90
80
70
60
50
40
30
20
10
0
0
of 190 C/W, yielding a temperature rise of 0.285 C.
Table I. Thermal Resistance (TO-92)
10
MOVING
AIR
Figure 7. Response Time
ALUMINUM
BLOCK
20
STILL AIR
JA
30
JA.
under several conditions. Table I
Because errors of this type can vary
40
TIME – sec
JA
50
( C/Watt)
60
75
190
60
JA
and the specific heat
70
80
90
(sec)*
JA
2
3.5
15
. Self-
100
–5–
neglected in the analysis; however, they will sink or conduct
heat directly through the AD22103’s solder plated copper leads.
When faster response is required, a thermally conductive grease
or glue between the AD22103 and the surface temperature
being measured should be used.
MICROPROCESSOR A/D INTERFACE ISSUES
The AD22103 is especially well suited to providing a low cost
temperature measurement capability for microprocessor/
microcontroller based systems. Many inexpensive 8-bit micro-
processors now offer an onboard 8-bit ADC capability at a mod-
est cost premium. Total “cost of ownership” then becomes a
function of the voltage reference and analog signal conditioning
necessary to mate the analog sensor with the microprocessor
ADC. The AD22103 can provide an ideal low cost system by
eliminating the need for a precision voltage reference and any
additional active components. The ratiometric nature of the
AD22103 allows the microprocessor to use the same power sup-
ply as its ADC reference. Variations of hundreds of millivolts in
the supply voltage have little effect as both the AD22103 and
the ADC use the supply as their reference. The nominal
AD22103 signal range of 0.25 V to 3.05 V (0 C to +100 C)
makes good use of the input range of a 0 V to 3.3 V ADC. A
single resistor and capacitor are recommended to provide im-
munity to the high speed charge dump glitches seen at many
microprocessor ADC inputs (see Figure 1).
An 8-bit ADC with a reference of 3.3 V will have a least signifi-
cant bit (LSB) size of 3.3 V/256 = 12.9 mV. This corresponds
to a nominal resolution of about 0.46 C/bit.
USE WITH A PRECISION REFERENCE AS THE SUPPLY
VOLTAGE
While the ratiometric nature of the AD22103 allows for system
operation without a precision voltage reference, it can still be
used in such systems. Overall system requirements involving
other sensors or signal inputs may dictate the need for a fixed
precision ADC reference. The AD22103 can be converted to
absolute voltage operation by using a precision reference as the
supply voltage. For example, a 3.3 V reference can be used to
power the AD22103 directly. Supply current will typically be
500 A which is usually within the output capability of the refer-
ence. A large number of AD22103s may require an additional
op amp buffer, as would scaling down a 10.00 V reference that
might be found in “instrumentation” ADCs typically operating
from 15 V supplies.
USING THE AD22103 WITH ALTERNATIVE SUPPLY
VOLTAGES
Because of its ratiometric nature the AD22103 can be used at
other supply voltages. Its nominal transfer function can be recal-
culated based on the new supply voltage. For instance, if using the
AD22103 at V
V
V
O
O
S
= 5 V the transfer function would be given by:
5 V
V
5 V
V
S
S
0.25 V
0.378 V
28 m V
42.42 mV
C
C
T
A
AD22103
3.3 V
T
5 V
A