FV-BR1 PANASONIC EW, FV-BR1 Datasheet - Page 34
![no-image](/images/manufacturer_photos/0/5/513/panasonic_ew_sml.jpg)
FV-BR1
Manufacturer Part Number
FV-BR1
Description
VACUUM FIBER TERMINATION 2 NEEDED (THRU)
Manufacturer
PANASONIC EW
Datasheet
1.FV-BR1.pdf
(40 pages)
Specifications of FV-BR1
Rohs Compliant
YES
33
FX-300
Threshold value fine adjustment
Output operation setting
Timer operation setting
•
•
Cascading amplifiers
•
•
Step
Step
PRECAUTIONS FOR PROPER USE
When the MODE indicator / TIMER (yellow) lights up, you can set
the type of timer and whether the timer is to be used or not. For the
FX-301B/G/H, the type of timer is set in PRO mode.
Further, an OFF-delay which is useful when the response of the
connected device is slow, etc., an ON-delay which is useful to detect only
objects taking a long time to travel, and ONE-SHOT, which is useful
when the input specifications of the connected device require a signal of
a fixed width, are possible with the FX-301 (-HS). [Furthermore, ON-
delay • OFF-delay and ON-delay • ONE-SHOT timer are incorporated for
FX-305(P).]
The FX-301(P), FX-301B/G/H(P) and FX-305(P) cannot use
communication for any settings other than the automatic
interference prevention function. When using these amplifiers as
well, use only the same type of amplifiers all together. However, the
FX-301-HS(P) is not equipped with an optical communication
function for setting the automatic interference prevention function,
so be aware of this when using these amplifiers with other amplifiers.
If the FX-301(P) updated version unit or the FX-305(P) is mounted
with the FX-301(P) previous version unit or the FX-301B/G/H(P) in
cascade, place the FX-301(P) updated version units and the FX-305
units to the right side (seen from the connector side) of the previous
version units. For a difference between the updated version unit and
the previous version unit, refer to
updated version unit and the previous version
1
2
3
1
2
3
Press the MODE key to light up
MODE indicator / ADJ (yellow).
For the FX-305(P), select ‘
In case the threshold value is to be increased
(sensitivity to be reduced), turn the jog switch to
the ‘
slowly. If the jog switch is turned continuously to
the ‘
In case the threshold value is to be decreased
(sensitivity to be increased), turn the jog switch to
the ‘
slowly. If the jog switch is turned continuously to
the ‘
rapidly.
When the jog switch is pressed, the
threshold value is confirmed.
Press the MODE key to light up
MODE
(yellow).
For the FX-305(P), select ‘
If the jog switch is turn to the ‘
‘
setting will change.
When the jog switch is pressed,
the threshold value is confirmed.
’ direction, the output operation
’ side, the threshold value increases rapidly.
’ side to decrease the threshold value
’ side to increase the threshold value
’ side, the threshold value decreases
indicator
/
Description
Description
L/D
ON
’ or ‘
’ or ‘
’ or
‘A difference between the
’ beforehand.
’ beforehand.
unit’ (P.34).
Displays present
setting
Displays selected
setting
Dark state
Display
Display
Light state
or
PRO mode
• PRO settings can be done when MODE indicator / PRO (yellow) lights up.
Notes: 1) FX-301(P) updated version unit, FX-301(P)-HS, FX-305(P) only
Key-lock function
• If the jog switch and the MODE key are pressed for more than 3 sec. at
Wiring
•
•
•
•
•
•
•
•
•
•
Others
•
•
•
•
•
•
PRO mode table
the same time in RUN mode condition, the key operations are locked,
and only the threshold value confirmation function or the adjust
function (valid only when the adjust lock function is canceled) is valid.
When the emission halt of the emitting power switching function is set from ‘OFF’ to ‘ON’, the
output may be unstable. Do not use the output control for 0.5 sec. after starting emission.
Make sure that the power supply is off while wiring.
Verify that the supply voltage variation is within the rating.
Take care that if a voltage exceeding the rated range is applied, or if an AC
power supply is directly connected, the sensor may get burnt or damaged.
If power is supplied from a commercial switching regulator, ensure that the frame
ground (F.G.) terminal of the power supply is connected to an actual ground.
In case noise generating equipment (switching regulator, inverter motor, etc.) is used in the vicinity
of this product, connect the frame ground (F.G.) terminal of the equipment to an actual ground.
Take care that short-circuit or wrong wiring of the load may burn or damage the sensor.
Do not run the wires together with high-voltage lines or power lines or put
them in the same raceway. This can cause malfunction due to induction.
Ensure that an isolation transformer is utilized for the DC power supply. If an
auto transformer is utilized, the main amplifier or power supply may be damaged.
Make sure to use the optional quick-connection cable for the connection of the
amplifier [FX-301(P)(-HS) / FX-305(P)]. Extension up to total 100 m
164.042 ft
more, cable. However, in order to reduce noise, make the wiring as short as possible.
Do not use during the initial transient time (0.5 sec. approx.) after the
power supply is switched on.
Take care that the sensor is not directly exposed to fluorescent light
from a rapid-starter lamp or a high frequency lighting device, as it
may affect the sensing performance.
This sensor is suitable for indoor use only.
Avoid dust, dirt, and steam.
Take care that the product does not come in direct contact with
water, oil, grease, or organic solvents, such as, thinner, etc.
This sensor cannot be used in an environment containing inflammable
or explosive gasses.
Never disassemble or modify the sensor.
(Note 4)
PRO6
PRO1
PRO2
PRO3
PRO4
PRO5
2) FX-301B(P)/G(P)/H(P) only
3) FX-301(P) updated version unit, FX-305(P) only
4) FX-305(P) only
for 5 to 8 units, 20 m
Display
65.617 ft
1 Response time change function ‘
2 Timer setting function ‘
3 Hysteresis function ‘
4 Stability function ‘
5 Shift function ‘
6 Emitting power selection function ‘
1 Digital display setting function ‘
2 Digital display inversion function ‘
3 ECO mode setting function ‘
1 Data bank load setting function ‘
2 Data bank save setting function ‘
1 Setting condition copy function ‘
2 Remote data bank load setting function ‘
3 Remote data bank save setting function ‘
4 Communication condition confirmation function ‘
5 Communication lock function ‘
6 Back-up function ‘
1 Code setting function ‘
2 Adjust lock setting function ‘
3 Setting reset function ‘
4 Interference prevention function ‘
1 Output setting function ‘
for 9 to 16 units,) is possible with 0.3 mm
Description
’
’
’ (Note 3)
’
’
’
’
’, ‘
328.084 ft
’
’
’ (Note 4)
’
’ (Note 1)
’
’
’
’
’
’ (Note 2)
’
’
(50 m
2
, or
’
’