FE-MLS8C PEPPERL & FUCHS, FE-MLS8C Datasheet - Page 4

• Manufacturer Part Number: FE-MLS8C
• Description: Photoelectric Sensor
• Manufacturer: PEPPERL & FUCHS
• Type: Fiber Opticr

Specifications of FE-MLS8C

• Output Current: 10A
• Sensor Output: Relay
• Sensor Housing: Rectangular
• Peak Reflow Compatible (260 C): No
• Output Type: Relay
• Sensor Input: Optical
• Supply Voltage Max: 132VAC
• Sensing Range Max: 12m
• Body Style: Rectangular
• Brand/series: FE-MLS8C
• Function: Proximity
• Ip Rating: IP67
• Output: Relay
• Primary Type: Photoelectric
• Range, Measurement: 12 m
• Sensing Mode: Retro-Reflective
• Technology: Photoelectric
• Termination: Screw
• Voltage, Supply: 132 VAC
• Leaded Process Compatible: No
• Rohs Compliant: No
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

Photoelectric Sensors
536
FE-MLS9C Wiring and Alignment
1. Remove the rear housing cover.
2a. Connect the load and load supply (common)
2b. Solid state relay connections shown below.
3. Connect AC power (through the conduit opening)
4. Set the mode selector switch to the light
5. Apply power. The alignment indicator light
Dimensions (mm)
1/4—20 UNC (M6X)
X 17,5/.69 LG Bolt
3 holes 120 deg. apart
FE-MLS8C and FE-MLS9C Sensors
to selected terminals. Standard relay
connections shown below.
to the “LINE” terminals. The white and black
input wires must be connected to the proper
terminals. See the control nameplate for correct
line volage.
operate (L.O.) position.
visible at the top of the control will remain OFF
with no reflector present.
3/4—14 NPSM
(PG21 per DIN 933)
157.2
C 1
C 1
PEPPERL+FUCHS
NO 1
NO 1
19
31.8
NC 1
88.9
Terminations
12.7
NC 2
54,1/2.13 turning
radius for 360 deg.
31.8
NO 2
189
63.5 REF
C 2
35.1
63.5
Line
Line
Pepperl+Fuchs Inc. • 1600 Enterprise Parkway • Twinsburg, Ohio 44087-2245 • www.am.pepperl-fuchs.com
Telephone [phone] • FAX [phone] • E-Mail: [e-mail]
184.2
®
(Dimensions in mm)
Accessories
6. Position the reflector opposite the lens. The
7. Center the reflector in the beam (by watching
8. Block the invisible beam with the object to be
9. Fully tighten the mounting bolts, and again
10. If direct On-Off dark operation is desired (relay
11. Insert optional function card firmly (if used)
12. Replace cover and tighten both screws.
Mounting Bracket Model FE-MB8
Material: 0.15in (3.8mm) C.R.S.,
Black Zinc Phosphate Finish
indicator will turn On when control and reflector
are in alignment.
the indicator as the reflector is moved up,
down, left and right). Use adhesive or a #8
screw (for the 3-inch disc) to mount the
reflector.
detected. When the beam is blocked, the
indicator will be Off.
block the beam to recheck alignment.
energized when the beam is blocked), move
the mode selector switch to the dark operate
(D.O.) position.
and adjust pots as required.
44.4 R
61 DIA
90 deg.
101.6
57.2
44.4
50,8/2.00 dia.
Bolt Circle
60.5
31.8
88.9
44.4
7,1/.28 Wide Slot
45 deg.
45 deg.