MA3 BANNER ENGINEERING, MA3 Datasheet
MA3
Specifications of MA3
Available stocks
Related parts for MA3
MA3 Summary of contents
Page 1
MICRO-AMP Remote sensors, modulated amplifiers, and logic modules Printed in USA ® System • A versatile system of compact, high-performance remote sensors modulated amplifiers, and logic modules • Remote sensors for opposed, retro, diffuse, convergent, and fixed-field sensing modes, in ...
Page 2
... Build- ing-block style control logic may be added to a system with a selection of MICRO-AMP logic modules. Model MPC3 is similar to amplifier model MA3, except that it is specifically designed for PC board mounting in OEM sensing applica- tions. MICRO-AMP modules may be mounted and wired using the optional model RS8 socket (shown in the drawing at right) or they may be mounted directly to a printed circuit board (see Accessories, p ...
Page 3
... Functional Schematic, MA3 Amplifier Model MA3P: PNP (current sourcing) output Model MA3P has the same specifications and performance as the MA3 amplifier, except that the MA3P has complementary PNP outputs in place of the MA3's NPN configuration. OUTPUT: two PNP transistors, complementary outputs; one normally open (light operate) and one normally closed (dark operate). 150 milliamps maximum, each output ...
Page 4
... Sensors for use with MA3 and MA3P Modulated Amplifiers Temperature range for all miniature modulated remote sensors degrees C (+32 to 158 degrees F). Sensors are epoxy-encapsulated and optics are hermetically sealed. Models/Dimensions SP100D SP100C 4 Excess Gain SP100E & OPPOSED Mode Sensors SP100R SP100E and SP100R miniature opposed sensors have a slim right-angle design which allows them to be mounted in very tight locations ...
Page 5
... Functional Schematic, MA3-4 Model MA3-4P: PNP (current sourcing) output Model MA3-4P has the same specifications and performance as the MA3-4 amplifier, except that the MA3-4P has complementary PNP outputs in place of the MA3-4's NPN configuration. OUTPUT: two PNP transistors, complementary outputs; one normally open (light operate) and one normally closed (dark operate). 150 milliamps maximum, each output ...
Page 6
... Sensors for use with MA3-4 and MA3-4P Modulated Amplifiers Sensors are epoxy-encapsulated and optics are hermetically sealed. Cables are 6 -1/2 feet (2m) long. 30-foot (9m) cables available by special order. Models/Dimensions OPPOSED Mode ALL MODELS Range: 8 feet (2,4m) Beam: infrared, 880nm Effective Beam: 0.14 inch (3,6mm) dia. ...
Page 7
... Sensors for use with MA3-4 and MA3-4P Modulated Amplifiers Sensors are epoxy-encapsulated. Cables are 6-1/2 feet (2m) long. 30-foot (9m) cables available by special order. Models/Dimensions SP300EL & SP300RL Temp. range: -40 to +100 C Range: 50 feet (15m) Effective Beam: .5 inch (13mm) Housing material: anodized dia. ...
Page 8
... Sensors for use with MA3-4 and MA3-4P Modulated Amplifiers Sensors are epoxy-encapsulated. Cables are 6-1/2 feet (2m) long. 30-foot (9m) cables available by special order. Models/Dimensions SP300D Range: 12 inches (30cm) both models Temp. range: -40 to +80 C both models Housing material (SP300D): Housing material (SP320D): ...
Page 9
... Sensors for use with MA3-4 and MA3-4P Modulated Amplifiers Sensors are epoxy-encapsulated and optics are hermetically sealed. Cables are 6-1/2 feet (2m) long. 30-foot (9m) cables available by special order. Models/Dimensions FIBER OPTIC Mode LR400 & PT400 with FOF-400 fittings glass fiber optics and fiber optics Range: see excess gain curves Temp ...
Page 10
... Hookup of SP300D, SP300L, LP400WB, SP1000V IMPORTANT : Cable Splicing Information Remote sensor cables may be run feet (9m) away from the MA3- 4 amplifier. All sensor models are available from the factory with 30 feet of cable, installed as an option. When splicing additional cable to the standard 6-1/2 foot length important to use a separate shielded cable for emitter and receiver wires ...
Page 11
... MA4 plug-in one-shot logic module with adjustable pulse length designed as a way to easily add one-shot timing to a MICRO-AMP system which uses an MA3 or MA3-4 amplifier. It may also be used to add a one-shot timer to any current sinking DC device system which offers a contact closure output. ...
Page 12
MICRO-AMP MA4G 4-input Gate Logic Module ® MICRO-AMP module MA4G 30V dc, plug-in, 4-input logic gate module. It offers three selectable logic modes: "AND", "NOR", and "X-NOR" (exclusive "NOR"). In the AND gate mode, the ...
Page 13
MICRO-AMP System MA4L Latch Logic Module MICRO-AMP ® model MA4L offers two latching logic modes. It can be latched and unlatched with low-going signals to its SET and RESET inputs. It also will function as an edge-triggered "D" flip-flop ...
Page 14
... MA5 is a plug-in delay logic module with adjustable delay timing designed as a way to easily add an ON DELAY or an OFF DELAY timer to a MICRO-AMP system which uses an MA3 or MA3-4 amplifier. It may also be used to add a delay timer to any current sinking dc device system which offers a contact closure output ...
Page 15
MICRO-AMP MPC3 Miniature Modulated Amplifier for direct PC-board mounting Model MPC3 is a modulated LED photoelectric amplifier which utilizes custom CMOS integrated circuitry. It contains all the circuitry necessary to modulate nearly any Light- Emitting Diode (LED) and to ...
Page 16
Functional Schematic, MICRO-AMP MPC3 * U.S. Patent #4598198 Hookup Diagram, MICRO-AMP MPC3 Model MPC3-DB Demo Board The MPC3- battery-powered demonstration/testing board which is available to help in evaluating the MPC3 and its sensor(s). The demo board includes a ...
Page 17
... The SP100FF is an excellent choice for precise position control (e. robotic end effector). The SP100FF works in conjunction with Banner MICRO-AMP modulated ampli- fier model MA3A or MPC3A. Model MA3A is powered by +10 to 30V dc and uses a model RS8 socket. Model MPC3A is powered by +5V dc and is designed for mounting directly onto PC boards. ...
Page 18
... Connections are made using the optional RS8 socket and wiring base, or the MA3A may be mounted directly board. The sensing system is powered by +10 to 30V dc. Power supply model MPS-15 is available, and includes its own board-mounted socket for the MA3A and a built-in SPDT output relay (see page 19) ...
Page 19
... MICRO-AMP module specifications and hookup). COMPATIBLE MODULES: models MA3, MA3A, MA3-4, MA4- 2, MA4G, MA4L, MA5. Do not plug modules with current-sourcing PNP outputs (MA3P, MA3-4P, etc.) into the socket on the MPS-15. POWER FOR EXTERNAL DEVICES: 40 milliamps is available to power external 10 to 30V dc devices (e.g.- two additional MICRO- AMP modules or two MINI-BEAM sensors, etc ...
Page 20
... WARRANTY: Banner Engineering Corporation warrants its products to be free from defects for one year. Banner Engineering Corporation will repair or replace, free of charge, any product of its manufacture found to be defective at the time it is returned to the factory during the warranty period. This warranty does not cover damage or liability for the improper application of Banner products ...