QS30EDV BANNER ENGINEERING, QS30EDV Datasheet - Page 5

• Manufacturer Part Number: QS30EDV
• Description: Photoelectric Sensor
• Manufacturer: BANNER ENGINEERING
• Type: Diffuser

Specifications of QS30EDV

• Output Current: 150mA
• Sensor Output: NPN/PNP
• Supply Voltage Range Dc: 10V To 30V
• Sensor Housing: Rectangular
• Sensing Range Min: 1100mm
• Sensor Input: Optical
• Body Material: ABS Plastic
• Supply Voltage Max: 30VDC
• Brand/series: World-Beam®
• Current, Switching: 150 mA
• Function: Proximity
• Ip Rating: IP67
• Mounting Type: Threaded
• Output: NPN/PNP
• Primary Type: Photoelectric
• Range, Measurement: 1100 mm
• Sensing Mode: Diffuse
• Technology: Photoelectric
• Termination: 5-Wire Cable
• Voltage, Supply: 30 VDC

Figure 4. Single-Point Window SET (Light
(no signal)
(no signal)
(no signal)
(no signal)
Darkest
Darkest
Darkest
Darkest
the presented condition
threshold 12.5% above
Output OFF
Banner Engineering Corp. • Minneapolis, MN U.S.A.
Sensor positions
www.bannerengineering.com • Tel: [phone]
Output OFF
Output OFF
Output OFF
Operate shown)
• Press and hold Static push
• Present sensing condition
• Double-click Static push
0.04 seconds ≤ “Click” ≤ 0.8 seconds
button > 2 seconds
button
Presented
Condition
Sensing window size
Threshold position
Threshold position
Manual Adjust
Manual Adjust
Manual Adjust
Manual Adjust
adjusted by
adjusted by
adjusted by
adjusted by
Output ON
Condition
Presented
Push Button
Position
Condition
Presented
or
or
Sensor positions
threshold 12.5% below
the presented condition
Output ON
Output ON
Output ON
Sensor positions
window thresholds
12.5% from the
presented condition
Output OFF
T
T
T
Most Light
Most Light
Most Light
Most Light
(saturated
(saturated
(saturated
(saturated
signal)
signal)
signal)
signal)
• Single-pulse remote line
• Present sensing
• Double-pulse remote line
0.04 seconds ≤ T ≤ 0.8 seconds
condition
T
• Sets a single ON condition that extends 12.5% above and below the taught condition.
• All other conditions (lighter or darker) result in OFF output
• Sensing window size (sensitivity) is adjustable using the “+” and “-” buttons (Manual
• Recommended for applications where the target to be sensed may not always appear in
Single-Point SET designates a sensing window, by setting two switching thresholds at
12.5% above and below the presented condition. The Output ON condition is inside the
window, and the Output OFF conditions are outside the window (see Figure 4) when
Light Operate is selected. Output ON and OFF conditions can be reversed by changing
Light/Dark Operate status in SETUP mode.
Single-Point Window SET and Manual Adjust
Using Manual Adjust with Single-Point Window SET expands or contracts the size of the
window. The lighted LEDs on the light bar separate to a greater or lesser extent to exhibit
the relative sensing window size.
Remote Line
Adjust)
the same place, or when other signals may appear.
T T T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
Power LED: OFF
Output LED: ON (Push Button)
Output LED: OFF (Remote)
Bargraph
Threshold Conditions Accepted
Power LED: ON
Bargraph: 2 indicators flash together
Sensor returns to RUN mode with
new settings
Threshold Conditions Unacceptable
Power LED: OFF
Bargraph:
Sensor returns to “SET Sensing Condition”
T T T
T
T
T
T
T
T
T
Single-Point Window SET
T
T
T
T
: #5 and 6 alternately
T
to show that the threshold
conditions are accepted
#1, 3 and 5, 7 alternately flash
to show failure
flash
T
T
T
WORLD-BEAM
T
T
T
T
T
T
T
T
T
T
T
Result
T
T
T
T
®
QS30EDV
Push Button
Remote
P/N 127755 rev. B
static
static
static
static
dynamic
dynamic
dynamic
dynamic
5