83691 SENSONOR TECHNOLOGIES AS, 83691 Datasheet - Page 8
![no-image](/images/no-image-200.jpg)
83691
Manufacturer Part Number
83691
Description
SENSOR, PRESSURE, COMP, SP100-7T
Manufacturer
SENSONOR TECHNOLOGIES AS
Datasheet
1.83691.pdf
(16 pages)
Specifications of 83691
Operating Temperature Range
-40°C To +125°C
Pressure Type
Absolute
Ic Generic Number
SP100-7T
No. Of Pins
14
Operating Pressure Range
0 To 700kPa
Sensor Case Style
SOIC
Supply Voltage
RoHS Compliant
Rohs Compliant
Yes
5
6
The product provides two outputs, which may be used to interrupt or reset a microcontroller. Each output provides a
pulse at regular intervals. The “wake-up and reset” are active low outputs. The Wake Up period typical value is
programmable from 1 to 256 seconds, in 1 second intervals.
Table 5.1 Wake-up and reset outputs
Notes:
The product has two oscillators: One low-power oscillator, which runs at about 2.5 kHz and is used for interval
timing, and a 2 MHz oscillator used for measurements and data transmission. Due to its very low current
consumption, the low-power oscillator is sensitive to temperature and supply voltage variation. To keep the interval
lengths constant under different conditions, the low-power oscillator is compared to the 2 MHz oscillator during each
measurement, and a correction is applied to the interval count. This operation is called an auto calibration. The
stability of the interval depends on the change in temperature or supply voltage since the last measurement.
The SPI interface is the communication protocol to the external microcontroller. This maximum serial clock frequency
is 500 kHz.
The SPI consists of a shift register, a command latch and failure latches, and encoder/decoder logic.
6.1
TS1481 rev. 1
When NCS is high, any signals at the SCLK and SDI pins are ignored, and SDO is forced into a high impedance
state.
During the NCS high-to-low transition, the SPI response word is multiplexed from the latch(es) that was(were)
defined by the last command present in the shift register. The SCLK pin must be low when NCS goes low.
At each clock rising edge after NCS has gone low, the response word is serially shifted out of the ASIC at the
SDO pin, LSB first. At each clock falling edge after NCS has gone low, the new control word is serially shifted into
the ASIC at the SDI pin, LSB first.
The command bits of the received SPI word are then decoded to determine the destination address for the data
bits. After the 8
stored in the ASIC SPI shift register to be transferred into the latch which address was decoded from the SPI shift
register command bits.
If the number of clock pulses before NCS goes high is different from 0, 8 or 16, a digital filter prevents execution of
the received command (A valid NCS pulse with 0 clock pulses will cause the previous command to be executed
again).
The Failure Status Indicator (FSI) is the logical OR of all bits in the status register, except bit 6.
The FSI appears at the SDO pin after NCS has gone low and before SCLK goes high (see timing diagram).
Wake-Up and Reset Outputs
Serial Interface
Interval timing drift over
Interval timing drift over
1)
supply voltage
Wake Up Width
See text describing oscillators below.
SPI Protocol
temperature
Reset period
Reset width
Parameter
th
clock falling edge has occurred, the following NCS low-to-high transition causes the data bits
1)
1)
DATASHEET
0.13
0.13
Min
Typ
0.6
-15
51
Max
2.5
2.5
-40
1
SP100 PRESSURE SENSOR SERIES
- 8 -
SP100-7(T), SP100-7A(T), SP100-12A
%/°C
Unit
%/V
min
ms
ms