E32-TC200E Omron, E32-TC200E Datasheet - Page 6

• Manufacturer Part Number: E32-TC200E
• Description: FIBER OPTIC CABLE
• Manufacturer: Omron
• Type: General Purposer

Specifications of E32-TC200E

• Rohs Compliant: YES
• Fiber Optic Sensor Type: General Purpose
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

6
E3X-DAC-S
Ratings and Specifications
Amplifier Units
Item
Sensing distance
Light source (wavelength)
Sensing method
Power supply voltage
Power consumption
Control output
Remote control input
Protection circuits
Re-
sponse
time
Sensitivity setting
(color registration, allowable range)
Func-
tions
Display
Digital display
Ambient illumination (Receiver side)
Ambient temperature range
(See note 6.)
Ambient humidity range
Insulation resistance
Dielectric strength
Vibration resistance
Shock resistance
Degree of protection
Connection method
Weight (packed state)
Materi-
als
Accessories
Sensing object
Number of registered colors
Super-high-speed mode
(See note 4.)
High-speed mode
Standard mode
High-resolution mode
Operating mode
Timer function
Control outputs
Remote control
Display switch (See note 5.)
Initialization
Case
Cover
Model
Type
Depends on the Fiber Unit. Refer to pages 8 to 10.
Reflective models: Standard 11 color cards (See note 1.), Through-beam models: Opaque or trans-
lucent object
White LED (420 to 700 nm)
C Mode: RGB ratio determination (or I Mode: Light intensity determination for red, green, or blue,
Black Mode: Determination of total light intensity for red, green, and blue) (See note 2.)
1
12 to 24 VDC ±10%, ripple (p-p) 10% max.
960 mW max. (current consumption: 40 mA max. at power supply voltage of 24 VDC)
NPN or PNP open collector
Load power supply voltage: 26.4 VDC max.
Load current: 50 mA max. (residual voltage: 2 V max.)
---
Reverse polarity for power supply connection, output short-circuit, Reversed output polarity protec-
tion
Operate or reset: 60 µs
Operate or reset: 300 µs
Operate or reset: 1 ms
Operate or reset: 4 ms
Teaching (one-point teaching or teaching with/without workpiece) or manual adjustment
ON for match (ON for same color as registered color) or ON for mismatch (ON for different color
from registered color)
Timer type: OFF delay, ON delay, or one-short
Timer time: 1 ms to 5 s (variable)
---
---
Seven patterns total: Match + Threshold, Margin + Threshold, Analog bar display, Peak + Bottom,
etc.
Initial reset (factory defaults) or user reset (saved settings)
Operation indicator (orange)/
I mode display indicator (orange)
7-segment displays (Main display: Red, Sub-display: Green), display direction can be reversed.
Incandescent lamp: 3,000 lux
Sunlight:
Operating: −25°C to 55°C
Storage:
Operating and storage: 35% to 85% (with no condensation)
20 MΩ min. (at 500 VDC)
1,000 VAC at 50/60 Hz for 1 minute
Destruction: 10 to 50 Hz with a 1.5-mm double amplitude for 2 hrs each in X, Y and Z directions
Destruction: 500 m/s
IEC 60529 IP50 (with Protective Cover attached)
Pre-wired or Amplifier Unit Connector (Units con-
nected: 16 max.)
Pre-wired model: Approx. 100 g, Amplifier unit connector model: Approx. 55 g
Polybutylene terephthalate (PBT)
Polycarbonate (PC)
Instruction manual
E3X-DAC@-S@ (@: 11/41/6/8)
−30°C to 70°C (with no icing or condensation)
Standard models
10,000 lux
2
, for 3 times each in X, Y and Z directions
2 (simultaneous determination)
No-voltage input (contact/transistor)
(See note 3.)
Operate or reset: 120 µs
Operate or reset: 600 µs
Operate or reset: 2 ms
Operate or reset: 8 ms
Output for each channel, AND output, and OR
output
One-point teaching, teaching with/without work-
piece, zero reset, and light emission OFF
Channel 1 and channel 2 operation indicators
(orange)
Pre-wired
E3X-DAC@-S@ (@: 21/51)
Advanced models