ELC-EX06NNNI-2 EATON CUTLER HAMMER, ELC-EX06NNNI-2 Datasheet - Page 12

Digital Output PLC

ELC-EX06NNNI-2

Manufacturer Part Number
ELC-EX06NNNI-2
Description
Digital Output PLC
Manufacturer
EATON CUTLER HAMMER
Datasheet

Specifications of ELC-EX06NNNI-2

Supply Voltage
24VDC
No. Of Analog Outputs
6
50-12
50
Standards and Certifications
Table 50-13. Approvals/Certifications
Electrical/EMC
Other Approvals
Technical Data and Specifications
Table 50-14. Environmental Ratings
Transportation & Storage
Operating
Table 50-15. DC Input Point Electrical Specifications
Table 50-16. Output Point Electrical Specifications
Description
ESD Immunity
EFT Immunity
Damped-Oscillatory Wave
RS Immunity
Agency Certifications
Description
Temperature
Humidity
Temperature
Humidity
Power Supply Voltage
Power Consumption
Insulation Resistance
Grounding
Vibration / Shock Resistance Standard: IEC1131-2, IEC 68-2-6 (TEST Fc) / IEC1131-2 & IEC 68-2-27 (TEST Ea)
Description
Input Type
Input Current
Active Level
Response Time
Output Type
Current Specification
Voltage Specification
Maximum Loading
Response Time
Output Circuit Diagram
PLC, I/O & Communications Products
ELC Programmable Logic Controllers
ELC Controllers / Modules
Specification
8 kV air discharge
Power Line: 2 kV; Digital I/O: 1 kV; Analog & Communication I/O: 250V
Power Line: 1 kV; Digital I/O: 1 kV
26 MHz – 1 GHz, 10 V/m
CE; C-Tick; cULus; Class I Div 2 Group A, B, C, D
(pending on PV controllers and left side specialty modules)
Specification
-13° – 158°F (-25° – 70°C)
5 – 95%
32° – 131°F (0° – 55°C)
50 – 95%
ELC: 24V DC (-15% – 20%) (With DC input reverse polarity protection), Expansion Unit: supplied by the ELC
3 – 6W
> 5 MΩ at 500V DC (Between all inputs/outputs and earth)
The diameter of grounding wire cannot be smaller than the wire diameter of terminals L and N (All ELC units should be
grounded directly to the ground pole).
Specification
DC (SINK or SOURCE)
24V DC 5 mA
OFF ➔ ON, above 16V DC
ON ➔ OFF, below 14.4V DC
About 10 mS (An adjustment range of 0 – 10,000 mS could be selected through D1020 and D1021)
Relay – R
1.5A/1 point (5A/COM)
Below 250V AC, 30V DC
75 VA (Inductive)
90W (Resistive)
Adjustable 0 – 15 ms, default is 10 ms
For more information visit: www.eaton.com
Transistor – T
0.3A/1 point @ 40°C; When the output of Y0 and Y1 is high-speed pulse,
Y0 and Y1 = 30 mA
30V DC
9W/1 point
OFF ➔ ON 20 µs
ON ➔ OFF 30 µs
LED
When the output of Y0 and Y1 is high-speed pulse, Y0 and
Y1 = 0.9W (Y0 = 32 kHz, Y1 = 10kHz), Y0 can be 50 kHz using
D registers.
Y0 and Y1 are specified points for high-speed pulse
Transistor Output
Y0
C0
< 0.5A
Load
February 2009
CA08102001E

Related parts for ELC-EX06NNNI-2