DPM 40 LASCAR, DPM 40 Datasheet - Page 2
![DPM, LED, 3.5DIGIT](/photos/21/38/213818/42251715_sml.jpg)
DPM 40
Manufacturer Part Number
DPM 40
Description
DPM, LED, 3.5DIGIT
Manufacturer
LASCAR
Specifications of DPM 40
Supply Voltage Range
4.5V To 5.5V
Backlighting Colour
Red
No. Of Digits / Alpha
3.5
Display Size
48mm X 20mm
Panel Cutout Height
68mm
Panel Cutout Width
33mm
Operating Temperature Range
0°C To +50°C
Svhc
No
Rohs Compliant
Yes
Backlighting Color
Red
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
SCALING
Two resistors may be used to alter the full scale reading of the meter - see table.
Note that the meter will have to be re-calibrated by adjusting the calibration pot .
SAFETY
To comply with the Low Voltage Directive (LVD 93/68/EEC), input voltages to the module’s pins must not exceed 60Vdc. If
voltages to the measuring inputs do exceed 60Vdc, then fit scaling resistors externally to the module. The user must ensure that
the incorporation of the DPM into the user’s equipment conforms to the relevant sections of BS EN 61010 (Safety Requirements
for Electrical Equipment for Measuring, Control and Laboratory Use).
PIN FUNCTIONS
C. DP3
D. CLOCK/
A. DP1
B. DP2
1. +5V
2. COM
3. IN HI
4. IN LO
5. 0V
E. DP COM
HOLD
199.9
19.99
1.999
Connect to 0V to hold display reading. Leave open for normal operation.
Connect to Pin A, B or C to select required DP .
Positive power supply input.
The ground for the analogue section of the converter, held actively at 2.8V (nom) below +5V. This pin is
for use only when the module is used with a fully floating supply.
to any other terminations or circuitry except as specified in the relevant operating modes.
Positive measuring input.
Negative measuring input.
Negative power supply input.
A compact low-cost LED module ideally suited for applications where a bright display under all
conditions is required. The DPM 40 is fitted with high efficiency LEDs and supplied with a filter
and bezel to give a high contrast display. The small size and low cost of the unit makes it very
suitable for high volume OEM applications.
• 11mm (0.43“) Digit Height
• Programmable Decimal Points
• Auto-zero
Analogue inputs must be no closer than 1V to the positive
supply or lower than 1.5V below 0V.
2
• Auto-polarity
• 200mV d.c Full Scale Reading (F.S.R.)
• Digital Hold
It should on no account be connected
TENSIONE D'INGRESSO
EINGANGSSPANNUNG
APPLICATIONS
APPLICATIONS
Measuring a single ended input referenced to supply ground.
Mesure d’une entrée à connexion unique référencée à l’alimentation.
Messen eines auf die Versorgung bezogenen massebezogenen Eingangs.
Misurazione di un ingresso con polo in comune rispetto all'alimentazione.
Measuring current.
Mesure de courant.
Strommessung.
Misurazione della corrente.
D’ALIMENTATION
INPUT VOLTAGE
R
VOLTAGE
R=
0.2
FSR
+
-
3
4
2
IN HI
IN LO
COM
+5V
0V
3
4
1
5
IN LO
IN HI
+5V
0V
+5V
0V
1
5
+5V
0V
7
ANWENDUNGEN
ESEMPI DI MODALITA' DI FUNZIONAMENTO
Measuring 4-20mA to read 0-999.
Mesure de 4-20mA pour lire 0-999.
Messung von 4 - 20 mA bei Anzeige 0 - 999.
Misurazione di 4-20mA per leggere 0-999.
Measuring a floating voltage source of 200mV full scale.
Mesure d’un voltage flottant de 200mV pleine échelle.
Messung einer potentialfreien Spannung mit 200 mV Vollausschlag.
Misurazione di una sorgente di tensione oscillante di 200mV in
grandezza naturale.
TENSIONE D'INGRESSO
EINGANGSSPANNUNG
D’ALIMENTATION
6R2
INPUT VOLTAGE
OUT
IN
220k
5k
VOLTAGE
SET
ZERO
4
3
2
+
-
IN HI
IN LO
COM
+5V
0V
1
5
3
4
2
+5V
0V
IN HI
IN LO
COM
+5V
0V
1
5
+5V
0V