B1 OPTO 22, B1 Datasheet
Specifications of B1
Related parts for B1
B1 Summary of contents
Page 1
... I/O. The B1 and B2 brain boards are designed to mount on most Opto 22 I/O mounting racks that have header connectors. I/O mounting racks that accept single-channel standard and G4 I/O ™ ...
Page 2
... DATA SHEET Form 463-050728 System Architecture Functions B1 (Digital) Functions • Read Point • Write Point • Latch Point • Count • Pulse Duration • Time Delay • Pulse Generation For complete information on supported Optomux commands, see Opto 22 form #1572. Opto 22 • 43044 Business Park Drive • Temecula, CA 92590-3614 • Phone: (951) 695-3000 • (800) 321-OPTO • Fax: (951) 695-3095 • www.opto22.com Inside Sales: (800) 321-OPTO • ...
Page 3
... Options Multidrop or repeat mode 2- or 4-pass protocol ** ±15 VDC ± 0.25 V required for the analog modules. Current depends on the number and type of modules installed VDC power supply is required for analog modules that need a current loop source. * Extend line length and/or number of OPTOMUX stations with the AC30A/B network adapter ...
Page 4
... DATA SHEET Form 463-050728 Installation and Wiring Power Requirements The B1 and B2 brain boards require +5 volts DC (± 0.1 VDC) at 0.5 amps. Although it is possible to distribute DC from a common power supply to several locations, better noise immunity is obtained by having separate power supplies at each physical location where a rack/brain board unit is installed ...
Page 5
... VAC (220 VAC or 10–28 VDC depending on supply type) connection to the PBSA (or PBSB or PBSC) supply. Separate or combined + 5 VDC (± 0.1 VDC) and ± 15 VDC (± 0.25 VDC) supplies can be used to provide power to analog racks. When using a multiple-output supply, make sure that the 5 VDC RETURN line is separate from the 15-volt COMMON line ...
Page 6
... Installation and Wiring (continued) Installing the Brain Board on the Mounting Rack The brain board plugs into the mounting rack using the 50-pin connector. The figures on the previous page show how to install the brain board on the mounting rack. When properly installed, the B1 (digital) brain board extends away from the rack, while the B2 (analog) brain board covers up the communications and power wiring on the rack ...
Page 7
... Form 463-050728 Opto 22 • 43044 Business Park Drive • Temecula, CA 92590-3614 • Phone: (951) 695-3000 • (800) 321-OPTO • Fax: (951) 695-3095 • www.opto22.com Inside Sales: (800) 321-OPTO • Product Support: (800) TEK-OPTO • (951) 695-3080 • Fax: (951) 695-3017 • Email: sales@opto22.com ...
Page 8
... DATA SHEET Form 463-050728 Specifications: Jumpers The two groups of jumpers on the B1 and B2 brain boards are labeled Group A and Group B. Jumpers in Group A route wiring for repeat or multidrop mode communications and also provide proper termination and biasing. All brain boards on the same network must operate in the same mode ...
Page 9
... Addresses do not need to be sequential. Opto 22 • 43044 Business Park Drive • Temecula, CA 92590-3614 • Phone: (951) 695-3000 • (800) 321-OPTO • Fax: (951) 695-3095 • www.opto22.com Inside Sales: (800) 321-OPTO • Product Support: (800) TEK-OPTO • (951) 695-3080 • Fax: (951) 695-3017 • Email: sales@opto22.com © ...
Page 10
... Opto 22 • 43044 Business Park Drive • Temecula, CA 92590-3614 • Phone: (951) 695-3000 • (800) 321-OPTO • Fax: (951) 695-3095 • www.opto22.com Opto 22 • 43044 Business Park Drive • Temecula, CA 92590-3614 • Phone: (951) 695-3000 • (800) 321-OPTO • Fax: (951) 695-3095 • www.opto22.com Inside Sales: (800) 321-OPTO • ...