B2 OPTO 22, B2 Datasheet
Specifications of B2
Related parts for B2
B2 Summary of contents
Page 1
... To use Optomux I Ethernet network, use Opto 22’ brain boards. These boards can use both serial and Ethernet networks simultaneously, and are drop-in replacements for B1s and B2s. See the E1 and E2 data sheet (Opto 22 form 1546) for information. CLASSIC page 1/10 ...
Page 2
... Opto 22 • 43044 Business Park Drive • Temecula, CA 92590-3614 • Phone: (951) 695-3000 • (800) 321-OPTO • Fax: (951) 695-3095 • www.opto22.com Inside Sales: (800) 321-OPTO • Product Support: (800) TEK-OPTO • (951) 695-3080 • Fax: (951) 695-3017 • Email: sales@opto22.com BRAIN BOARDS ANALOG AND DIGITAL B2 (Analog) Functions • Read Point • Write Point • Input Averaging • ...
Page 3
... Opto 22 • 43044 Business Park Drive • Temecula, CA 92590-3614 • Phone: (951) 695-3000 • (800) 321-OPTO • Fax: (951) 695-3095 • www.opto22.com Inside Sales: (800) 321-OPTO • Product Support: (800) TEK-OPTO • (951) 695-3080 • Fax: (951) 695-3017 • Email: sales@opto22.com BRAIN BOARDS ANALOG AND DIGITAL B2 (Analog) none none none ...
Page 4
... DATA SHEET Form 463-050728 Installation and Wiring Power Requirements The B1 and B2 brain boards require +5 volts DC (± 0.1 VDC) at 0.5 amps. Although it is possible to distribute DC from a common power supply to several locations, better noise immunity is obtained by having separate power supplies at each physical location where a rack/brain board unit is installed ...
Page 5
... The high cost of electrical wiring and the susceptibility of analog signals to noise make it desirable to place the brain board as close as possible to the controlled device. The default communication mode for the B1 and B2 brain boards is multidrop. When wiring a multidrop communications cable, keep in mind that the cable is a high-speed data-transmission line ...
Page 6
... Installation and Wiring (continued) Installing the Brain Board on the Mounting Rack The brain board plugs into the mounting rack using the 50-pin connector. The figures on the previous page show how to install the brain board on the mounting rack. When properly installed, the B1 (digital) brain board extends away from the rack, while the B2 (analog) brain board covers up the communications and power wiring on the rack ...
Page 7
... Form 463-050728 Opto 22 • 43044 Business Park Drive • Temecula, CA 92590-3614 • Phone: (951) 695-3000 • (800) 321-OPTO • Fax: (951) 695-3095 • www.opto22.com Inside Sales: (800) 321-OPTO • Product Support: (800) TEK-OPTO • (951) 695-3080 • Fax: (951) 695-3017 • Email: sales@opto22.com ...
Page 8
... DATA SHEET Form 463-050728 Specifications: Jumpers The two groups of jumpers on the B1 and B2 brain boards are labeled Group A and Group B. Jumpers in Group A route wiring for repeat or multidrop mode communications and also provide proper termination and biasing. All brain boards on the same network must operate in the same mode ...
Page 9
... Addresses do not need to be sequential. Opto 22 • 43044 Business Park Drive • Temecula, CA 92590-3614 • Phone: (951) 695-3000 • (800) 321-OPTO • Fax: (951) 695-3095 • www.opto22.com Inside Sales: (800) 321-OPTO • Product Support: (800) TEK-OPTO • (951) 695-3080 • Fax: (951) 695-3017 • Email: sales@opto22.com © ...
Page 10
... Opto 22 • 43044 Business Park Drive • Temecula, CA 92590-3614 • Phone: (951) 695-3000 • (800) 321-OPTO • Fax: (951) 695-3095 • www.opto22.com Opto 22 • 43044 Business Park Drive • Temecula, CA 92590-3614 • Phone: (951) 695-3000 • (800) 321-OPTO • Fax: (951) 695-3095 • www.opto22.com Inside Sales: (800) 321-OPTO • ...